Jump to content
HWBOT Community Forums

Recommended Posts

Of course, tweaking auxiliary voltages is for helping with cold bug and other issues when going ln2, it will not affect core frequency on air/water, cache can be maxxed out with small bumps like 1.3 termination should be more than enough for pushing this on regular cooling. 

Share this post


Link to post
Share on other sites

fMyElgc.png

Hi @Alex@ro 

I set the voltages above based on  your recommendations. Do those look right? Anything I should change? 

I'm going for a daily 53x core only and then will inch up cache until it's unstable and then back it down by 1x

 

Edited by robert896r1

Share this post


Link to post
Share on other sites

Anyone got the dreaded " USB overcurrent protection - system will shut down in 15 secs " message with error code 55 :(

On Apex XI that is.

Share this post


Link to post
Share on other sites
On ‎12‎/‎24‎/‎2019 at 9:40 AM, Fasttrack said:

Anyone got the dreaded " USB overcurrent protection - system will shut down in 15 secs " message with error code 55 :(

On Apex XI that is.

Any solution on this ?

Share this post


Link to post
Share on other sites
Posted (edited)

Weird mem training issue:

 

I'm running the following: unknown.png

 

This is fully stable within windows with TM5 extreme profile and OCCT large/avx2 tested. However when I reboot the machine, it'll get stuck "bF" post code. I have to keep hitting retry to go into bios and mess around voltages to get it to eventually work. When it's back in windows it's fully stable again. Any ideas what's causing this? Most the timings are hardset. 

Edited by robert896r1

Share this post


Link to post
Share on other sites
Posted (edited)

Hi guys

i am running :

the  XI Gene, 9900KS at 5.1Ghz and 2x8 GB Viper 4400 kit with the results you can see

I would like  to achieve 15-15-36, now i am stable at 16-16-36, 1.48V.

i already tried 15-15-36 and 15-16-38 with 1.50, no luck so far, plus various little more advanced tweaks i could heard off.

SA at 1.24 and IO at 1.18

what setting i could try ? and of course no over 1.50 V

Thank you very much

 

 

 

 

1.png

2.png

Edited by ales75

Share this post


Link to post
Share on other sites

Try to find out the RAM voltage that allows the system to boot at 4000 15-15-15-30-2, even if that is above 1.5v. 

If it is above 1.5v, that is its lower limit, so you 'll have your answer.

If it's below 1.5v, start tightening again :)

Share this post


Link to post
Share on other sites
2 hours ago, Bruno said:

Try to find out the RAM voltage that allows the system to boot at 4000 15-15-15-30-2, even if that is above 1.5v. 

If it is above 1.5v, that is its lower limit, so you 'll have your answer.

If it's below 1.5v, start tightening again :)

Thanks dude, yes it is the kind of approach i always use.. i was mostly talking about more hidden settings etc.. that could help me in then stabilizing the overclock, however i already changed the ram kit :)

  • Like 1

Share this post


Link to post
Share on other sites

Hey folks! I've been playing around a bit with the daily setup on my apex. Currently I'm running F4-3600C15D-16GTZ (A2-pcb) @ 4400 16-16-16 2T 1.535v with 1.25v IO/SA as a daily ( https://i.imgur.com/qxOoxkk.png ). I'd love to get some 1T action going but I can only post as high as 4200 (with trace centering enabled). Trying to figure out if it's a kit limitation or IMC or else - 2T is absolutely no issue and I've posted as high as 4800 without issue and haven't bothered with higher. I've played around with more IO/SA (gone as far as 1.35v IO/1.45v SA) and 1.58v on the sticks but 1T is just a no-go so far even with loose timings. Any suggestions? I'm thinking RTTs but I haven't been able to find any good starting point and with how many combinations there are I could waste an entire day getting nowhere. Is there something obvious I've missed? Seeing more and more "easy 4600 1T" with other kits so hoping one of you have some pointers for me. Thanks!

Share this post


Link to post
Share on other sites
18 minutes ago, Apothysis said:

Hey folks! I've been playing around a bit with the daily setup on my apex. Currently I'm running F4-3600C15D-16GTZ (A2-pcb) @ 4400 16-16-16 2T 1.535v with 1.25v IO/SA as a daily ( https://i.imgur.com/qxOoxkk.png ). I'd love to get some 1T action going but I can only post as high as 4200 (with trace centering enabled). Trying to figure out if it's a kit limitation or IMC or else - 2T is absolutely no issue and I've posted as high as 4800 without issue and haven't bothered with higher. I've played around with more IO/SA (gone as far as 1.35v IO/1.45v SA) and 1.58v on the sticks but 1T is just a no-go so far even with loose timings. Any suggestions? I'm thinking RTTs but I haven't been able to find any good starting point and with how many combinations there are I could waste an entire day getting nowhere. Is there something obvious I've missed? Seeing more and more "easy 4600 1T" with other kits so hoping one of you have some pointers for me. Thanks!

Maybe against the spirit of OC and tweaking, but what do you think you will gain with 1T vs 2T for a daily setup ? Seems you already dialed in pretty well, beating easily retail kits in bandwidth and performance.

Share this post


Link to post
Share on other sites
On 4/24/2020 at 11:47 PM, Leeghoofd said:

Maybe against the spirit of OC and tweaking, but what do you think you will gain with 1T vs 2T for a daily setup ? Seems you already dialed in pretty well, beating easily retail kits in bandwidth and performance.

Late update but I'm a nut for daily tuning and as far as 1T vs 2T goes, 4200 16 1T is very, very close in performance to 4400 16 2T in stuff like time spy cpu, superpi etc., I just like pushing the daily stuff to the limit. 😉

As an answer to my own question I tested two different kits and it was definitely a kit-limitation that had a roof at 4200 1T as it was easy to go beyond that on the other two kits.

  • Like 2

Share this post


Link to post
Share on other sites
Posted (edited)

whether there is a chance to add txp and especially ppd settings in apex xi bios?

zU5Fq0R.png

because to use memtweakit after each reboot...

Edited by Marcel1ne
  • Like 1

Share this post


Link to post
Share on other sites
On 1/1/2020 at 7:51 PM, robert896r1 said:

Weird mem training issue:

 

I'm running the following: unknown.png

 

This is fully stable within windows with TM5 extreme profile and OCCT large/avx2 tested. However when I reboot the machine, it'll get stuck "bF" post code. I have to keep hitting retry to go into bios and mess around voltages to get it to eventually work. When it's back in windows it's fully stable again. Any ideas what's causing this? Most the timings are hardset. 

I was running into this same issue when trying higher frequencies at 1t. I tuned rtl/iol and found that it helped avoid this q code a lot. Didnt test enough to say it eliminated it entirely but it definitely reduced how often it happened. Let me know what you find if you try this!

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...