Jump to content
HWBOT Community Forums
ADVenturePO

The official Challenger 2019 Division VII round 1 Intel legacy thread.

Recommended Posts

It should be by now .

K I close the topic within 12 hours, atm it will be S775 and 1366 only

 Edited 21 hours ago by Leeghoofd

Share this post


Link to post
Share on other sites
5 hours ago, Mr.Scott said:

SR-2 or no?

if yes i am wasting  my time on rex III :)
but i dont have high hopse that we may use it

Share this post


Link to post
Share on other sites

Dual socket is server for sure right...  single socket only... don't pull out my arm lads when I offer a finger 😛

Share this post


Link to post
Share on other sites
36 minutes ago, Leeghoofd said:

Dual socket is server for sure right...  single socket only... don't pull out my arm lads when I offer a finger 😛

Stretching a bit . Not pulling out.

You need your arms for other things 🤣

I stil Know what you told me on whatsapp before thé comp's  startet " no dual Xeon stages "

Edited by skulstation

Share this post


Link to post
Share on other sites
5 hours ago, Leeghoofd said:

Dual socket is server for sure right...  single socket only... don't pull out my arm lads when I offer a finger 😛

SR-2 is hardly a server board but that's fine Alby. Just wanted to check. ;)

Share this post


Link to post
Share on other sites
On 2/16/2019 at 2:27 AM, Mr.Scott said:

All or nothing.

what if you are right and they're wrong

Αποτέλεσμα εικόνας για what if you are right and they're wrong
 
  • Like 2

Share this post


Link to post
Share on other sites
Don't close the subject on x79 - I have one... in my personal PC - and it's i7-4960x but it's only 4.7GHz with Noctua NHD14 at liquid metal (for silence). To participate i'd need to take it out and that very time consuming. I have no different x79 MB nor CPU. So I think I'll be able to participate with it till the end of this competition.

Share this post


Link to post
Share on other sites

This benchmark (HWBOT GPUPI for CPU 100M) is confusing. Even for me i downloaded all the versions but still my GPU runs it.

Edited by samus2

Share this post


Link to post
Share on other sites

You will need to Install openCL drivers for your CPU, (otherwise the CPU will not be supported by the benchmark) 

Share this post


Link to post
Share on other sites
19 hours ago, samus2 said:

To me x79 is legacy hardware. And if 6 core Xeons are allowed ...

 

19 hours ago, samus2 said:

Idd x79 allowed with a 6 core?

have you both voted in the poll at:

 

Share this post


Link to post
Share on other sites
Quote
1 hour ago, Leeghoofd said:

have you both voted in the poll at:

yup

 

  • Thanks 1

Share this post


Link to post
Share on other sites
Verification screenshot requirements CPU-Z CPU tab CPU-Z Memory tab With Key: Benchmark window (score and run details) Without Key: Benchmark window (view result at 3DMark.com) Web browser with link and score visible Verification link Verification link required for Global Top 20 This rule still applies?

Share this post


Link to post
Share on other sites
Posted (edited)

one of my sub for 3dmark 11 physics reported by 'mattfleg' for not running the monitoring tool during the run.

at the top it shows 27.8 min/max which might have led to reporting the sub.

but you can look at

1. memory usage

2. power usage

3. temps below show idle 30/34c and load 49/52c

4. core utilisation 100% on all cores

probably this should justify the sub. 

hw monitor pro is bugged. i have at least half a dozen screenshots showing my i7 8700k as i3 7350k or i5 750 etc. here it's showing i3 4130 as fx-8350(screenshot). now it's asking me to buy the product to show the info. non pro version seems better. now i have started using the non pro version

had my problems with installing hardware info. ask for an update which windows says you don't need it(can give screenshots). but if it works that gives the best possible info. i can run in  xp but not running on windows 7 home premium/ultimate sp1. not tried on win 10

open hardware monitor 0.8.0 beta is only giving clocks but no temperatures. haven't tested much but the in-built ohm in x265 is also problematic but still it gives clocks,temps and all relevant information.  

sub is ranked 17th of 17 submissions. have at least half a dozen processors which can better this but obviously don't have i7 4770k/i7 4790k which is the best bet.

 

image_id_2141112.png

Edited by ksateaaa23

Share this post


Link to post
Share on other sites
6 hours ago, ksateaaa23 said:

one of my sub for 3dmark 11 physics reported by 'mattfleg' for not running the monitoring tool during the run.

at the top it shows 27.8 min/max which might have led to reporting the sub.

but you can look at

1. memory usage

2. power usage

3. temps below show idle 30/34c and load 49/52c

4. core utilisation 100% on all cores

probably this should justify the sub. 

hw monitor pro is bugged. i have at least half a dozen screenshots showing my i7 8700k as i3 7350k or i5 750 etc. here it's showing i3 4130 as fx-8350(screenshot). now it's asking me to buy the product to show the info. non pro version seems better. now i have started using the non pro version

had my problems with installing hardware info. ask for an update which windows says you don't need it(can give screenshots). but if it works that gives the best possible info. i can run in  xp but not running on windows 7 home premium/ultimate sp1. not tried on win 10

open hardware monitor 0.8.0 beta is only giving clocks but no temperatures. haven't tested much but the in-built ohm in x265 is also problematic but still it gives clocks,temps and all relevant information.  

sub is ranked 17th of 17 submissions. have at least half a dozen processors which can better this but obviously don't have i7 4770k/i7 4790k which is the best bet.

 

image_id_2141112.png

The trial version of HWmonitor Pro doesn't seem to automatically update what it's monitoring.

You can however fix that - At the top of the program where you see things like "File", "View", "Network", ect.... Click "View". Then look at what's seen for options in that and you'll see the option to "Clear Labels". Click that and the program will update itself to what's actually in the machine.

Each time you swap pieces to run you'll have to do that but it works.

  • Like 1

Share this post


Link to post
Share on other sites

Thanks. Will try that. In one OS I might have exhausted how many times I can open. Asking to register now. Uninstalled and running non pro version.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...