Jump to content
HWBOT Community Forums
Leeghoofd

Comet Lake core i5-7-9 Batch and Serial numbers thread

Recommended Posts

Posted (edited)

Hi,

10900k batch # X016E724 SP94 at first next day dropped to SP 92 :/

Seem okay sure needs some juice v-f and 0403 bios has been a lot of fun to deal with 0607 bios wasn't any better

But got 0403 to at least do okay on 4k mhz finally and so-so performance

 

Altered 4k preset.PNG

10900k v-f point offsets.jpg

10900k-R20-6949-5.3-5.0 cache-bycore usage-avx-0.png

Edited by ThrashZone

Share this post


Link to post
Share on other sites

Retail 10700K
X014E307  -- CB R15 5.2Ghz  1.36v  AIO - 6650 R15 1.75v LN2 - mllrkllr88

Share this post


Link to post
Share on other sites
Posted (edited)
16 hours ago, ThrashZone said:

Hi,

10900k batch # X016E724 SP94 at first next day dropped to SP 92 :/

Seem okay sure needs some juice v-f and 0403 bios has been a lot of fun to deal with 0607 bios wasn't any better

But got 0403 to at least do okay on 4k mhz finally and so-so performance

 

Altered 4k preset.PNG

10900k v-f point offsets.jpg

10900k-R20-6949-5.3-5.0 cache-bycore usage-avx-0.png

Need voltage at full load for this to be a valid submission.  Idle voltages mean nothing.

Please post a picture of the CB20 during full core load, and the vcore window open in hwinfo64 or CPU_Z so we can see your vcore at full load.

Also your SP is bugged.  This is a common problem for people using old bios versions.  Your first three VF points are the exact same and too high.  This throws off the SP rating too.  Your chip could be anywhere between SP88 to SP105.

To fix this you MUST update your BIOS.

1) Update to version 0607.

2) After updating, wait until it says "Press F1 for intel power limits"

3) Press F1, enter BIOS, then power off the system.

4) Clear CMOS with the clear cmos button on the back panel (or jumper/button onboard)

5) boot, wait, then press F1 for intel default power limits.  Boot to windows without changing anything in the BIOS.

6) run prime95 small FFT with AVX DISABLED for 5 minutes (with the F1 defaults)

7) reboot to BIOS.

8: Your SP should now be shown correctly.   If you want to go back to an old bios after, you can do that after posting a fixed SP/VF points, but if it gets bugged again, it will throw off prediction and AI overclocking when using an old Bios.

Edited by Falkentyne
  • Like 1
  • Thanks 1

Share this post


Link to post
Share on other sites
Posted (edited)

#1 10900K - X014E373 - CB R15 5.3   1.279Vcore Water - SP78 - 6790 CB R15 LN2 1.620v - NOIZEMAKER

#2

#3 10900K - X019EXXX - CB R15 53/50 1.243 Vcore 20C Water / 54/50 1.310 Vcore 20C Water - ~6800 CB R15 1.645v LN2 - SP63 -  NOIZEMAKER

#4 10900K(A) - X031E753 - CB R15 5.3  1.305Vcore Water - SP 78 - ~6800 CB R15 1.645v LN2 - NOIZEMAKER

Edited by noizemaker
  • Like 1

Share this post


Link to post
Share on other sites

10900K 

X016E866

SP 94 R15 5,3 with 1,325 Vcore Bios, load 1,305, Ln2 6740 with 1,62 Vcore not higher scaling, bad IMC  

Share this post


Link to post
Share on other sites
On 5/31/2020 at 5:00 PM, Matt26LFC said:

10900K - X016F051 - CB R15 5.3Ghz 1.3Vcore (Strong WC will pass 5.4Ghz with approx 1.43Vcore)  No cold testing yet.

Had a go with Ln2, this chip did 6.8Ghz R15, 1.66v set in TurboV

Share this post


Link to post
Share on other sites
Posted (edited)

V008D554 -- CB R20 5.8ghz 1.368Vcore  -100c

Edited by FUGGER
  • Like 1

Share this post


Link to post
Share on other sites

X018e481 sp87 5.2 at 1.25v  set on bios and the same with voltmeter.

On ln2 - 6740mhz with 1.61v cbr15

Test with apex 12

Share this post


Link to post
Share on other sites

Intel Core i9 10900K - V017E718 - SP87

On AIO 360

5.2GHz 1.225v BIOS, 1.2v load
5.3GHz 1.325v BIOS, 1.3v load

On Asus ROG Maximus XII Extreme

screen730.jpg

screen731.jpg

Share this post


Link to post
Share on other sites

can we add to the list if the CPU becomes "Cold Afraid" and can no longer go full pot. know of maybe 4-5 guys this has happen to so far. maybe we can track batches that are to blame

  • Like 3
  • Sad 2

Share this post


Link to post
Share on other sites

im waiting for CC fastdry contact cleaner spray to confirm alex's theory about dirty socket cuz my board is dirty and i had even vas in socket a litle bit...  if it fails add my batch to the list :D im already talking with intel via emails and im wating for response from higher technical team, hopefully we will get any conclusion soon..

  • Like 1

Share this post


Link to post
Share on other sites
37 minutes ago, davestarrr said:

im waiting for CC fastdry contact cleaner spray to confirm alex's theory about dirty socket cuz my board is dirty and i had even vas in socket a litle bit...  if it fails add my batch to the list :D im already talking with intel via emails and im wating for response from higher technical team, hopefully we will get any conclusion soon..

It is not a theory though :) I had same situations in past with 7700K 8700K 9900K. Also with a pretested cpu that i sold, i could run full pot all day long without any cb or cbb, arrives to buyer, cb at -160. After properly cleaning pads and socket buyers was happy. I am not saying that it is impossible for cpu's to not run full pot just that you have to have clean socket and cpu and mount/remount on different boards, if still no go then yes... cpu hates cold and that's it. 

  • Haha 1

Share this post


Link to post
Share on other sites
Posted (edited)

i9 10900k X018F708
i9 10900k X018F670
i9 10900k X018F938
i9 10900k X013F055

i9 10900k X018F853

 

some information about these batchs

 

 

Edited by pskz0r

Share this post


Link to post
Share on other sites
On 7/9/2020 at 2:48 PM, Splave said:

can we add to the list if the CPU becomes "Cold Afraid" and can no longer go full pot. know of maybe 4-5 guys this has happen to so far. maybe we can track batches that are to blame

I think my CPU has joined this club, I will test again this evening to confirm. I had a bad crash benching last night, then lost all my frames. Broke system down and quickly checked on watercooled setup = cpu was working fine at normal temps!  Will be very sad if this is the case - was SP111.....

  • Sad 2

Share this post


Link to post
Share on other sites

I'd like to know from those with the now "cold scared" chips, if they were all using an Apex when this happened. My gut feel is the board if causing an issue through a faulty rail or something.

Share this post


Link to post
Share on other sites
Posted (edited)

have some issues where after a certain time the board goes into 00 on apex xii, with different cpus and isolations..
ogs mentioned the "rsvd" switch when it happens to proceed further, that worked 1 of 3 times..
same as bob lost frames during a bench, blackscreen = 00
cpu works normal on ambient again, and cold again too for a few runs
 

Edited by noizemaker

Share this post


Link to post
Share on other sites
On 8/17/2020 at 11:01 AM, KaRtA said:

I'd like to know from those with the now "cold scared" chips, if they were all using an Apex when this happened. My gut feel is the board if causing an issue through a faulty rail or something.

It is a good question - mine is linked to Apex. Anyone on another board had this problem??

Share this post


Link to post
Share on other sites

Reflection point:  the Apex is the most used board, so there should be a lot of these cold scared cpus if it would be just the board right...

Share this post


Link to post
Share on other sites
On 7/9/2020 at 7:18 AM, Splave said:

can we add to the list if the CPU becomes "Cold Afraid" and can no longer go full pot. know of maybe 4-5 guys this has happen to so far. maybe we can track batches that are to blame

if you can dig up them batches Allen

  • Like 1

Share this post


Link to post
Share on other sites
7 hours ago, bob(nz) said:

It is a good question - mine is linked to Apex. Anyone on another board had this problem??

Yes mllr has one from aqua

  • Like 2

Share this post


Link to post
Share on other sites

Did no one run through any 10600K / KF at all? Are they really that bad? I would have hoped they would have a small chance at least vs. 3600XT 

Share this post


Link to post
Share on other sites
6 hours ago, Leeghoofd said:

Reflection point:  the Apex is the most used board, so there should be a lot of these cold scared cpus if it would be just the board right...

2 hours ago, Splave said:

Yes mllr has one from aqua

Yeah Alby fair call - but just interested to see how widespread the issue is.  And Allen's comment helps, it appears to be more CPU related...

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...