I.nfraR.ed Posted June 2, 2013 Share Posted June 2, 2013 What tWCL are you running? I will check later if everything with the frequency is correct, maybe make a video too. I'm gaining (at least) 2 seconds from wazza. XP is tweaked like I always do for 32M. I can't run 1300MHz at all. Not sure if the board or IMC. Quote Link to comment Share on other sites More sharing options...
The Stilt Posted June 2, 2013 Share Posted June 2, 2013 (edited) What tWCL are you running?I will check later if everything with the frequency is correct, maybe make a video too. I'm gaining (at least) 2 seconds from wazza. XP is tweaked like I always do for 32M. I can't run 1300MHz at all. Not sure if the board or IMC. tCWL 5, 6, 7. 7 MEMCLKs appears to be the fastest. The difference is barely noticeable <0.1 sec. I´ll try on Gigabyte next time. There might be some differences in DRAM-NB calibrations, but nothing which could explain the difference. Edited June 2, 2013 by The Stilt Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 2, 2013 Share Posted June 2, 2013 Turbo is disabled. Will make a video of a whole run if my camera battery is up to it. Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 2, 2013 Share Posted June 2, 2013 Video 1 - The end of a normal run, slightly slower than my previous results. Btw I have 18:400 somewhere on the ssd. Not sure if you can see something. Had to compress both videos and Youtube compressed them further. This video also shows that "One does not simply restart a Gigabyte board" Video 2 - full run, bad wazza and cpuz opened all the time. 3 seconds slower. Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 3, 2013 Share Posted June 3, 2013 Damn it. Just realized that the videos are not correct. I'm running Pi on second core from the first module and I didn't show its frequency. This means another video... Quote Link to comment Share on other sites More sharing options...
The Stilt Posted June 4, 2013 Share Posted June 4, 2013 No need for the videos, I never thought you would be cheating intentionally. Found one of the reasons why my time was so slow. On XP you'll just never ever - ever never disable the "Luna" theme. It is over four seconds faster than the Classic theme. A quite "nice" glitch. Still, I am atleast five seconds slower than I should be. The DRAM/NB timings have been tweaked as far as they go, the adjustment range has been literally exhausted. Cannot go any tighter. Still need to check something. I noticed that Gigabyte does not enable the "CLK Mux". I certainly hope this is not done on purpose, yet I would not be too surprised... http://www.hwbot.org/submission/2386335_the_stilt_superpi___32m_a10_5800k_18min_14sec_718ms Quote Link to comment Share on other sites More sharing options...
flanker Posted June 4, 2013 Share Posted June 4, 2013 2700+ unlock at air, uffff! Whats voltage for APUNB? Quote Link to comment Share on other sites More sharing options...
The Stilt Posted June 4, 2013 Share Posted June 4, 2013 2700+ unlock at air, uffff! Whats voltage for APUNB? 1.4V, just outside the "kill zone" Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 4, 2013 Share Posted June 4, 2013 Is the limit still the same on LN2? I've never used more than 1.4V on LN2, because it didn't seem to help with NCLK. Quote Link to comment Share on other sites More sharing options...
The Stilt Posted June 4, 2013 Share Posted June 4, 2013 Is the limit still the same on LN2? I've never used more than 1.4V on LN2, because it didn't seem to help with NCLK. On LN2 you can do 1.6 - 1.65V, depending on the leakage. At 1.7V or beyond the NB gets damaged (GPU first then the rest of it). Any chance you could upload the F3I bios for UP4? I have all of the other alphabets besides that. Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 4, 2013 Share Posted June 4, 2013 (edited) Yes, here it is: https://dl.dropboxusercontent.com/u/30576042/2A85XUP4.F3i I have it from the last CountryCup. Noticed other guys were running that version, but we couldn't find it anywhere, so I asked Massman and he was nice to share it. Honestly I didn't see any difference in performance. By the way, I don't even know what is CLK Mux and what it is related with Edited June 4, 2013 by I.nfraR.ed Quote Link to comment Share on other sites More sharing options...
The Stilt Posted June 4, 2013 Share Posted June 4, 2013 Thanks for the bios. There is no difference in SuperPI performance between F2A85-V PRO and F2A85X-UP4, the times were within the margin of error. The CLK Mux feature is PLL related. There are two PLLs on F2A85-V PRO and F2A85X-UP4 which can be used to generate the BCLK frequency. One is located inside the FCH (Internal PLL) and the second one is the external located between the PCI-E slots. Even the F2A85X-UP4 features an external digital PLL, for some reason Gigabyte does not use it for BCLK until the adjustment range of the internal PLL has been exhausted (136MHz BCLK). I've asked the reason for this but they never gave me any answer. Asus F2A85-V PRO never uses the internal PLL for the BCLK, only the external. The CLK Mux controls the different frequencies. Without it enabled the all of the clocks are tied to BCLK. When enabled the clocks are separated by the mux control. The PCI-E frequency stays at 100MHz even when the BCLK is raised. I could not test the Gigabyte board above 108MHz BCLK as the board flips out after that when AHCI is enabled. No such issues on Asus. Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 5, 2013 Share Posted June 5, 2013 (edited) Interesting information, thanks. Yes, I have that issue with UP4. I was able to load Win7 at 111MHz bclk no problem, but with XP @ AHCI I should go down to 105 or so, then raise the bclk from Windows. Had to do the same with Win7 on IDE mode. So in fact PCI-E frequency is equal to BCLK when Mux not enabled (Gigabyte case)? I've used 120+ BCLK in the past, but don't remeber what sata mode and it was definitely a lower mem divider. Edited June 5, 2013 by I.nfraR.ed Quote Link to comment Share on other sites More sharing options...
Massman Posted June 8, 2013 Author Share Posted June 8, 2013 Updated the thread and added Richland core to the database. Quote Link to comment Share on other sites More sharing options...
flanker Posted June 15, 2013 Share Posted June 15, 2013 Have someone explanation, why Zambezi core is in superpi better than Piledriver core? If in all others is much worse than Piledriver... Quote Link to comment Share on other sites More sharing options...
l0ud_sil3nc3 Posted June 15, 2013 Share Posted June 15, 2013 Because AMD makes every generation of architecture slower on 32m to torture 2D benchers lol 22 minutes is a long time to wait for pi to finish. 1 Quote Link to comment Share on other sites More sharing options...
flanker Posted June 15, 2013 Share Posted June 15, 2013 but did you saw x87 unoficial patch from Stilt? After fx-8350 got AMD WR in superpi . Quote Link to comment Share on other sites More sharing options...
Bones Posted June 23, 2013 Share Posted June 23, 2013 Did a run with the Stilt's errata fix and this popped up - Makes a world of difference! http://www.hwbot.org/submission/2393184_ This was better than a sub I have but disabled points for this entry anyway. Note that I used the same settings as the one done before for this challenge. Quote Link to comment Share on other sites More sharing options...
I.nfraR.ed Posted June 23, 2013 Share Posted June 23, 2013 (edited) I still have to test that, but just wow... it's 3:30 minutes better than my time! Edited June 23, 2013 by I.nfraR.ed Quote Link to comment Share on other sites More sharing options...
Massman Posted June 27, 2013 Author Share Posted June 27, 2013 Just messing about in the lab ... Quote Link to comment Share on other sites More sharing options...
TaPaKaH Posted June 27, 2013 Share Posted June 27, 2013 G.Skill 2GBFX, eh? Quote Link to comment Share on other sites More sharing options...
Massman Posted June 27, 2013 Author Share Posted June 27, 2013 Anything special? Quote Link to comment Share on other sites More sharing options...
The Stilt Posted June 27, 2013 Share Posted June 27, 2013 A 5.0GHz Vishera with 2750MHz NCLK and DDR-2666 MEMCLK scores around 14min 20 seconds after the BDC R1.02. Quote Link to comment Share on other sites More sharing options...
Massman Posted June 27, 2013 Author Share Posted June 27, 2013 I'm around that with lower memclk. 14m25s, but for some reason I'm not able to hit 4G NBclk anymore, since the 8G 1M chip seems to have given up Quote Link to comment Share on other sites More sharing options...
TaPaKaH Posted June 27, 2013 Share Posted June 27, 2013 Anything special?never seen any "FX" lineup Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.