Jump to content
HWBOT Community Forums

How to add unsupported cards


elmor

Recommended Posts

  • Replies 128
  • Created
  • Last Reply

Top Posters In This Topic

7870 hawk profile works great. Monitoring output shows different than dmm, but not a big deal

 

Did some more testing. It seems that vgpu can only go up to 1.5v. With 1.5v on evc set, it shows 1.488v on dmm at idle. Under load it drops a lot. vmem is in fact pll. The pll setting does nothing.

 

When applying trying to apply over 1.5v vgpu, it doesn't apply any more and eventually crashes evc drivers. It will show in corner as device not connected and even in device manager it does not show up anymore.

Edited by Mikecdm
Link to comment
Share on other sites

  • 2 weeks later...

Did anyone notice that CHL8318 and ASP1212 are exactly the same? ASP1212 is on 780Ti DC2 for example. Think they just rebranded it.

Compare the datasheets:

 

http://www.irf.com/product-info/datasheets/data/pb-chl8318.pdf

http://www.irf.com/product-info/datasheets/data/pb-asp1212.pdf

 

So the ASP1212 should be already working with a CHL8318 profile (or at least be very easily to add ;)) right?

Link to comment
Share on other sites

Did anyone notice that CHL8318 and ASP1212 are exactly the same? ASP1212 is on 780Ti DC2 for example. Think they just rebranded it.

Compare the datasheets:

 

http://www.irf.com/product-info/datasheets/data/pb-chl8318.pdf

http://www.irf.com/product-info/datasheets/data/pb-asp1212.pdf

 

So the ASP1212 should be already working with a CHL8318 profile (or at least be very easily to add ;)) right?

 

I just tried this on the 780 lightning profile and 680/770 profile and it does not work for me with 780Ti DC2.

 

This is what scanning the card shows.

 

Device scan 4/3/2014 10:16:37 PM: 0x0C 0x44

Link to comment
Share on other sites

No worries, easy mistake. I believe there's no digital control available for vmem/pll, there's another chip but I'm not sure what it's for. You could try this to get some data:

 

Go to Menu and select Register scan. Enter:

 

Device address 0x0C

Register start 0x1

Register end 0xFF

 

Run it and send the log to me.

Link to comment
Share on other sites

Guest barbonenet

john i try evc on 4870x2! work fine but max real vcore is at 1,45v...what can i do??

 

i use SVID mode! the first volt is for 2d and the second for 3d!

 

thanks

Link to comment
Share on other sites

john i try evc on 4870x2! work fine but max real vcore is at 1,45v...what can i do??

 

i use SVID mode! the first volt is for 2d and the second for 3d!

 

thanks

 

I got some reports that there's a maximum voltage limit using some VT1165 controllers, not sure how to change that. I'll look into it and get back to you.

Link to comment
Share on other sites

Guest barbonenet

thanks....today i make vmod, and now i have 1,6 - 1,65.....but with evc, volt don't increase over 1,45v!

 

if you have a special bios, please send me it;)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...