Broken APEX49
-
Posts
589 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Blogs
Posts posted by Broken APEX49
-
-
1 hour ago, kaliz said:
The HWinfo readout with just 50% core utilization is because of the polling period is set to default 1000ms. If you shorten the polling rate to 200ms your read out are 5 times more accurate ( the sensors will collect data every 200ms instead of every 1000ms it does now,
you can find the oprtion in Settings
I'm asking others.
-
Hello.
I'm trying SuperPI with 7800x3d
For now, the only RAM timing on the 7800x3d is the EXPO setting.
ECLK overclocking with CO set to 107, all cores needed to be positive and up to 23.
I checked the cores in RYZEN master and found that in my case 1 core was good and 3 cores were second best, so I set 1 core to positive 23, 3 cores to positive 22, and the other cores to negative 0.
With this setting, I was able to complete the PI.
Is this the right direction as a basic idea?
I know this is off topic, but any advice would be appreciated!
I checked HWiNFO64 and it's running with one core as priority during benchmarking, but the utilization is at 50%, and it's not running at 100%.Translated with DeepL.com (free version)
-
It's not the 5G Challenge.
I'm trying SuperPI with 7800x3d
For now, the only RAM timing on the 7800x3d is the EXPO setting.
ECLK overclocking with CO set to 107, all cores needed to be positive and up to 23.
I checked the cores in RYZEN master and found that in my case 1 core was good and 3 cores were second best, so I set 1 core to positive 23, 3 cores to positive 22, and the other cores to negative 0.
With this setting, I was able to complete the PI.
Is this the right direction as a basic idea?
I know this is off topic, but any advice would be appreciated!Translated with DeepL.com (free version)
-
9 hours ago, wutske said:
理解できません。誰も VSoc を上げるべきだとは言いませんでした。Buildzoid には 1.15V があり、高い VSoc は無限のファブリック速度に悪影響を与えるとさえ言っています。
PBO で許可されている以外の X3D チップ上の VCore を変更することさえできず、その場合でも非常に厳密な境界内にあります。X3D チップの有無に関係なく、VDDR をクランクすることができます。
翻訳では多くの情報が失われると思います。オーバークロックに適したマザーボードをお持ちです。オーバークロックに適した RAM が搭載されています。あなたが使用している CPU はオーバークロック向けにまったく作られていませんが、CPU は非常に正当な理由からオーバークロックを可能な限り阻止しています。走る前に歩き方を学ばなければなりませんが、その CPU を使って室内サンダルで 100 メートル走に挑戦することになります。
私たちは本当にあなたを助けようとしていますが、個人的にはあなたが自分自身でそれを難しくしすぎていると思います。言語の壁なく助けてくれる日本語のフォーラムが必要です。また、PBO なしで実際にオーバークロックできる CPU がある場合は、より簡単になります。周波数と電力状態を変更するもの (PBO、電源管理、S3、C1、C6、Cool&Quiet、ターボなど) をすべて無効にすると、オーバークロックがはるかに簡単になります。
//編集: ハードウェア ライブラリをチェックしましたが、ロック解除された CPU の経験が豊富で、素晴らしい結果も得られているようです。あなたはこのボードで素晴らしいパフォーマンスを見せたRyzen 7700を持っているのに、なぜそれが悪いボードだと言うのかわかりません。7700 がそのボードで何ができるかはわかっているので、そのボードを元に戻し、最初に PBO を使用してそのボードを最適化してコツを掴んでください。次に、乗算器を使用する代わりに ECLK でその CPU をオーバークロックしてみて、どこまで実現できるかを確認してください。
I do not intend to rely on Buildzoid's information.
-
I'm not interested in 8,000.
-
This is not helpful
Since the voltage of the X3D system is severe, especially regarding the SOC voltage.
Anything over 1.3V is dangerous. -
5 hours ago, I.nfraR.ed said:
あなたが何を尋ねているのかを理解するのは本当に難しいです。
VDDIO、VDDQ、および VDD を等しい必要はありません。CPU とメモリースティックにも依存します。VDDIO の場合、通常は 1.30 ～ 1.40V の範囲に留まります。
高電圧モードが有効になっている場合、VDDQ と VDD は ZenTimings で正しく表示されません。
It does not appear in other people's ZenTimings.
I'm wondering if this is a BIOS specification only for ASRock B650E Taichi.
but it doesn't seem so.You must be wondering!
-
The display is different for you and me.
Why?
CPU VDDIO?
It's in the BIOS, but how do other ASRock users set it up?
-
Hello all.
I would like to resume RAM OC on AMD after a long time, but..,
I've forgotten some basic stuff.
I thought I wrote it down.
It's voltage related.
VDDIO_Voltage (VDDIO_MEM_S3)
DRAM VDD Voltage
DRAM VDDQ Voltage
Is it correct that these are basically the same values?
VDDIO_Voltage (VDDIO_MEM_S3) is unique to Asrock, right?
I seem to remember that DRAM VDDQ Voltage should be lower than DRAM VDD Voltage,
I have searched the site, though,
VDD_SOC is recommended to be 1.3V or lower, right?Translated with DeepL.com (free version)
-
Thanks for the info.
Off topic, but I think I may be getting some noise from the board.
Not sure what's causing it.
I can't overclock the DRAM since I changed to 7800X3D.
Even 6200 won't pass. 1T won't pass at all.
Is it broken?
I'm trying to change the BIOS from 2.03 to 2.02.
The screen froze in the middle of the flash.
I'm having all kinds of problems.
DRAM is F5-6000J3038F16GX2-TZ5NR -
And you can't have 8,000 of DRAM.
I'm confused no matter what I try.
I don't know how to adjust individual cores.
You can't have ECLK at 106 or 107, you can't have CO in the negative direction. -
I ran it.
What should I look for?
It runs normally, but..,
How does this tell me if it's a good core or not?
I don't understand.
Go to the optimization of each core and figure out which cores are more powerful and which are weaker ← I don't know how to do this! -
I'm sorry. I'm sorry.
I don't understand what you mean.
I'm trying, but...
Thanks. I don't understand the CO.
BIOS entry in B650E Taichi, I don't understand it!
Not enough information, translation problems and my brain.
I'm trying to record Domdtxdissar, but
I also don't understand the relationship between ECLK and DRAM
Right now, DRAM is still 6000 at the expo.-
1
-
-
1 hour ago, wutske said:
SkatterBencher から正確な設定をコピーしただけですか? なぜなら、それがあなたのCPUで動作するという保証は文字通り0だからです。
また、y-cruncher で安定性をテストしてみてください。安定性の問題がすぐに見つかるので、PBO 設定を変更して修正する必要があります。
シリコンを宝くじで紛失した可能性もあります。
I don't know how to set up y-cruncher.
Also, I'm trying to adjust the CO.
I understand that I have to set the value on all cores and test it, but I'm not sure if it's possible to set the value on
but I don't understand how to adjust CO for each single core.
I don't understand how to adjust CO for a single core, or which core is negative.
I don't understand why some cores are negative and others are positive.
I have been able to test all cores up to stability with ECLK106 and positive 3.-
1
-
-
I want Hydra!
I can't find the download section.
Is this a pay first pattern? Monthly purchase? -
B650E Taichi
I wish I had never purchased it.-
1
-
-
I would like to hear from a professional.
I purchased a 7800X3D
The board is an Asrock B650E Taichi
I have studied SkatterBencher and the explanation of Actually Hardcore Overclocking
I'm trying to run it, but I can't do it well.
I know professionals may not be interested in this CPU, but I want to succeed in overclocking it since I bought it at an affordable price.
At present, Eclk can be applied up to 105 by the profile of SkatterBencher, but it is the situation that OS cannot be booted beyond that.
I would appreciate any advice you can give me.
-
ryzen 7 7800x3d overclocking is difficult.
-
Do you have any used ASUS Z790 Apex available?
I don't want to Encore. -
rx6400
I want to overclock!
Can't you do something? -
Is it effective?
-
I understand that you usually can't overclock.
Do you have any good ideas?
I tried the amernime zone driver, but the performance decreased. -
Clock ignored.
We are not competing here. -
The official BenchMate support thread
in Benchmark software
Posted
R23 on the cinebench
I want to cancel a continuous test