Broken APEX49

R23 on the cinebench I want to cancel a continuous test

I'm asking others.

Hello. I'm trying SuperPI with 7800x3d For now, the only RAM timing on the 7800x3d is the EXPO setting. ECLK overclocking with CO set to 107, all cores needed to be positive and up to 23. I checked the cores in RYZEN master and found that in my case 1 core was good and 3 cores were second best, so I set 1 core to positive 23, 3 cores to positive 22, and the other cores to negative 0. With this setting, I was able to complete the PI. Is this the right direction as a basic idea? I know this is off topic, but any advice would be appreciated! I checked HWiNFO64 and it's running with one core as priority during benchmarking, but the utilization is at 50%, and it's not running at 100%. Translated with DeepL.com (free version)

It's not the 5G Challenge. I'm trying SuperPI with 7800x3d For now, the only RAM timing on the 7800x3d is the EXPO setting. ECLK overclocking with CO set to 107, all cores needed to be positive and up to 23. I checked the cores in RYZEN master and found that in my case 1 core was good and 3 cores were second best, so I set 1 core to positive 23, 3 cores to positive 22, and the other cores to negative 0. With this setting, I was able to complete the PI. Is this the right direction as a basic idea? I know this is off topic, but any advice would be appreciated! Translated with DeepL.com (free version)

I do not intend to rely on Buildzoid's information.

I'm not interested in 8,000.

This is not helpful Since the voltage of the X3D system is severe, especially regarding the SOC voltage. Anything over 1.3V is dangerous.

It does not appear in other people's ZenTimings. I'm wondering if this is a BIOS specification only for ASRock B650E Taichi. but it doesn't seem so. You must be wondering!

The display is different for you and me. Why? CPU VDDIO? It's in the BIOS, but how do other ASRock users set it up?

Hello all. I would like to resume RAM OC on AMD after a long time, but.., I've forgotten some basic stuff. I thought I wrote it down. It's voltage related. VDDIO_Voltage (VDDIO_MEM_S3) DRAM VDD Voltage DRAM VDDQ Voltage Is it correct that these are basically the same values? VDDIO_Voltage (VDDIO_MEM_S3) is unique to Asrock, right? I seem to remember that DRAM VDDQ Voltage should be lower than DRAM VDD Voltage, I have searched the site, though, VDD_SOC is recommended to be 1.3V or lower, right? Translated with DeepL.com (free version)

Thanks for the info. Off topic, but I think I may be getting some noise from the board. Not sure what's causing it. I can't overclock the DRAM since I changed to 7800X3D. Even 6200 won't pass. 1T won't pass at all. Is it broken? I'm trying to change the BIOS from 2.03 to 2.02. The screen froze in the middle of the flash. I'm having all kinds of problems. DRAM is F5-6000J3038F16GX2-TZ5NR

And you can't have 8,000 of DRAM. I'm confused no matter what I try. I don't know how to adjust individual cores. You can't have ECLK at 106 or 107, you can't have CO in the negative direction.

I ran it. What should I look for? It runs normally, but.., How does this tell me if it's a good core or not? I don't understand. Go to the optimization of each core and figure out which cores are more powerful and which are weaker ← I don't know how to do this!

I'm sorry. I'm sorry. I don't understand what you mean. I'm trying, but... Thanks. I don't understand the CO. BIOS entry in B650E Taichi, I don't understand it! Not enough information, translation problems and my brain. I'm trying to record Domdtxdissar, but I also don't understand the relationship between ECLK and DRAM Right now, DRAM is still 6000 at the expo.

I don't know how to set up y-cruncher. Also, I'm trying to adjust the CO. I understand that I have to set the value on all cores and test it, but I'm not sure if it's possible to set the value on but I don't understand how to adjust CO for each single core. I don't understand how to adjust CO for a single core, or which core is negative. I don't understand why some cores are negative and others are positive. I have been able to test all cores up to stability with ECLK106 and positive 3.

I want Hydra! I can't find the download section. Is this a pay first pattern? Monthly purchase?

B650E Taichi I wish I had never purchased it.

I would like to hear from a professional. I purchased a 7800X3D The board is an Asrock B650E Taichi I have studied SkatterBencher and the explanation of Actually Hardcore Overclocking I'm trying to run it, but I can't do it well. I know professionals may not be interested in this CPU, but I want to succeed in overclocking it since I bought it at an affordable price. At present, Eclk can be applied up to 105 by the profile of SkatterBencher, but it is the situation that OS cannot be booted beyond that. I would appreciate any advice you can give me.

ryzen 7 7800x3d overclocking is difficult.

Do you have any used ASUS Z790 Apex available? I don't want to Encore.

rx6400 I want to overclock! Can't you do something?

Is it effective? https://www.amernimezone.com/

I understand that you usually can't overclock. Do you have any good ideas? I tried the amernime zone driver, but the performance decreased.

Clock ignored. We are not competing here.

OC?