kezu

For some reason, i cannot get gpupi running correctly on my setup. Fresh win 10 installation and 32b gpupi takes like 1 hour per loop. week ago i had fresh win 8 install and it worked just fine. May have to hook up my card to different mobo & cpu setup. and instal win7 & win8.

yay! that bad solder actually saved my card. It's up and running, thank you so much newlife!

Thanks! I will look at it again if i find something. Edit, might had bad solder. Resoldered that bottom end. Now getting correct resistance. Will give it a try now. *fingers crossed*

this is what i got measuring those resistances. and resistance from vmem spot to ground is 8.25k

Did some checks on mem pwm. If i remember right the resistance between ground and vmem mod spot was below 3k ohm. now it's 8.2k ohm aprox. So, gotta find where the broken resistor is maybe?

Thanks, rechecked the mod area. No tin drops nothing. Took pots. On vmem pot hair or two copper wires was poking out from hotglue and ground wire just next to them. Checked on multimeter, resistance almost zero. Might be recoverable?

I think i might have accidentally killed my Card. Soldered vgpu & vmem read points. Everything was fine. No shorts, covered with hotglue. I dont have any clue what might have killed it. Cleaned with alcohol whole card, mods removed. Compressed air etc. Boot and card is bricked. vgpu sits 0.9v and vmem 0.6v. Have to check tomorrow again is there any scratches or tin drops or anything. I might get new card in time. Maybe. Anyway, i was dumb enough and did not save any screenshots. Just had so many hours tweaking with 3dmark01 and best was 60400 points. Ahh well, lesson learned.

So far Asus 1gb model 1591 /1191 Takes 1.4v for gpu. Im still on stock heatsink. Cooled by 120mm fan. temps under load are 48c Off to sleep now. Tomorrow, memory and maxing out gpu with 120fan. After that gonna test air conditioner ghetto mod. No tweaks.

Thank you so much! I get same reading, from otherside of the card. Thanks alot! such an nice community! Happy benching guys!

Funny, i tought that i did mod wrong, but seems that my pot isn't fines quality. Takes quite lot of turns until started happening, i even double checked the resistance. But im up on unning now. 1.15vgpu and 1440 mhz on gpu. Furmark stable. Running on air.

Its done same way that in newlife's guide. thanks to him

Tips for Asus 710gt 1gb vgpu voltage read point? Found one, back side of the card aprox where is two caps on gpu side. Gives reading 0.956 already bumbed up to 1v. Also one other boint gives steady 1.156 under load and under 1.08x when idle. But trimming pot wont change anything. Thank you! Might be my vgpu mod wont work, or soldered incorrectly. Edit, seems like it's working. I thought that vgpu stovk is 1.12 as vid says.

Well i asked, if there's coming out maximus tweak option for ranger board. Simply answer was. 4 layer board, i have maxed out mem oc. Something to do with signals. So no loose subtiming options for us. Edit, anybody has any pics what the maximus tweak mode 1 changes in bios? or is it coded to bios itself?

What mem's you have and whats the max mhz you are able to obtain? I might have few tricks which may get you few mhz more Edit, gonna reach out raja. Maybe he can throw some tricks to us. Funny that bit more expensive rog mb's have option to use maximus tweak's but alas. Ranger does not have.

0018 & 190x official. Tested both of them hyperx 2666mhz 16gb kit wont post above 2900mhz. Patriot viper 3600c17 2x4 gb singlesided sticks. No matter what. Wont go above 3450mhz I assume those are E - die. But seems like im not the only one who's affected with this problem. Doing google search there's lots of complaints even mem's not working when QVL. Especially thru xmp settings. Already done lots of fiddling to sub timings. But no help.