DonMarkoni Posted February 19, 2012 Posted February 19, 2012 Here's a BIOS template for R4E... if anyone's interested... old school, txt file, not BIOS s/s. ************************EXTREME TWEAKER************************ =============================================================== LN2 Mode Disable All Core Target CPU Turbo-Mode Speed : 5000MHz Target DRAM Speed : 2400MHz Ai Overclock Tuner [Manual] CPU Level Up [Disabled] BCLK Frequency [100.000] CPU Strap [100MHz] ClockGen Full Reset [Enabled] Turbo Ratio [by All Cores] By All Cores [50] Internal PLL Overvoltage [Enabled] CPU Clock Gen Filter [20UF] Memory Frequency [DDR3-2400MHz] Xtreme Tweaking [Disabled] EPU Power Saving Mode [Disabled] =============================================================== >DRAM Timing Control Rampage Tweak [Mode 2] Primary Timings CHA CHB CHC CHD DRAM CAS# Latency 7 7 7 7 [7] DRAM RAS# to CAS# Delay 11 11 11 11 [11] DRAM RAS# PRE Time 7 7 7 7 [7] DRAM RAS# ACT Time 27 27 27 27 [27] DRAM COMMAND Mode 1 1 1 1 [1] Latency Boundary [Auto] Secondary Timings CHA CHB CHC CHD DRAM RAS# to RAS# Delay 4 4 4 4 [4] DRAM REF Cycle Time 96 96 96 96 [96] DRAM WRITE Recovery Time 14 14 14 14 [14] DRAM READ to PRE Time 4 4 4 4 [4] DRAM FOUR ACT WIN Time 20 20 20 20 [20] DRAM WRITE to READ Dealy 4 4 4 4 [4] DRAM Write Latency 8 8 8 8 [8] Tertiary Timings CHA CHB CHC CHD tRRDR 0 0 0 0 [0] tRRDD 0 0 0 0 [0] tWWDR 0 0 0 0 [0] tWWDD 0 0 0 0 [0] tRWDR 8 8 8 8 [8] tRWDD 3 3 3 3 [3] tWRDR 1 1 1 1 [1] tWRDD 1 1 1 1 [1] tRWSR 8 8 8 8 [8] tCCD 0 0 0 0 [0] Latency Timings CHA CHB CHC CHD DRAM RTL (CHA D0 R0) 37 [Auto] DRAM IOL (CHA D0 R0) 5 [Auto] DRAM RTL (CHA D0 R1) 37 [Auto] DRAM IOL (CHA D0 R1) 5 [Auto] DRAM RTL (CHA D1 R0) 11 [Auto] DRAM IOL (CHA D1 R0) 0 [Auto] DRAM RTL (CHA D1 R1) 11 [Auto] DRAM IOL (CHA D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHB D0 R0) 37 [Auto] DRAM IOL (CHB D0 R0) 7 [Auto] DRAM RTL (CHB D0 R1) 37 [Auto] DRAM IOL (CHB D0 R1) 7 [Auto] DRAM RTL (CHB D1 R0) 11 [Auto] DRAM IOL (CHB D1 R0) 0 [Auto] DRAM RTL (CHB D1 R1) 11 [Auto] DRAM IOL (CHB D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHC D0 R0) 37 [Auto] DRAM IOL (CHC D0 R0) 5 [Auto] DRAM RTL (CHC D0 R1) 37 [Auto] DRAM IOL (CHC D0 R1) 5 [Auto] DRAM RTL (CHC D1 R0) 11 [Auto] DRAM IOL (CHC D1 R0) 0 [Auto] DRAM RTL (CHC D1 R1) 11 [Auto] DRAM IOL (CHC D1 R1) 0 [Auto] ----------------------------------------------------- DRAM RTL (CHD D0 R0) 37 [Auto] DRAM IOL (CHD D0 R0) 7 [Auto] DRAM RTL (CHD D0 R1) 37 [Auto] DRAM IOL (CHD D0 R1) 7 [Auto] DRAM RTL (CHD D1 R0) 11 [Auto] DRAM IOL (CHD D1 R0) 0 [Auto] DRAM RTL (CHD D1 R1) 11 [Auto] DRAM IOL (CHD D1 R1) 0 [Auto] Others DRAM CLK Period [5] Enhanced Training (CHA) [Disabled] Enhanced Training (CHB) [Disabled] Enhanced Training (CHC) [Disabled] Enhanced Training (CHD) [Disabled] MCH Duty Sense (CHA) [15] MCH Duty Sense (CHB) [17] MCH Duty Sense (CHC) [15] MCH Duty Sense (CHD) [17] Receiver Slew [Normal] Transmitter Slew [Normal] MCH Recheck [Auto] RC Warm Boot Fast [Disabled] =============================================================== >DIGI+ Power Control CPU VCore CPU Load-line Calibration [High] CPU Current Capability [Disabled] CPU Voltage Frequency [Manual] CPU Fixed Frequency [500] VRM Over Temperature Protection [Auto] CPU Power Duty Control [Extreme] Vcore MOS volt. Control [7V] CPU Power Phase Control [Extreme] CPU VCORE Boot Up Voltage [Auto] CPU VSA VCCSA Load-line Calibration [Extreme] VCCSA Current Capability [140%] VCCSA Fixed Frequency [500] CPU VCCSA Boot Up Voltage [Auto] CPU VTT CPU VTT Switching Freq [1.3x] CPU VTT Over-Current Protection [Auto] DRAM Voltage DRAM-AB Current Capability [140%] DRAM-AB Voltage Frequency [Manual] DRAM-AB Fixed Frequency Mode [500] DRAM-AB Power Phase Control [Extreme] DRAM-CD Current Capability [140%] DRAM-CD Voltage Frequency [Manual] DRAM-CD Fixed Frequency Mode [500] DRAM-CD Power Phase Control [Extreme] PCH 1.1V PCH 1.1V Switching Freq [Auto] =============================================================== >CPU Performance Settings CPU Ratio [Auto] Enhanced Intel SpeedStep Technology [Enabled] Turbo Mode [Enabled] -------------------------------------------------------- Turbo Mode Parameters Power Limit Control [Auto] =============================================================== Extreme OV [Disabled] BCLK Skew [Auto] CPU VCORE Voltage 1.432V [Manual Mode] CPU VCORE Manual Voltage [1.430] VTT CPU Voltage 1.218V [1.20000] 2nd VTTCPU Voltage 1.046V [Auto] CPU VCCSA Voltage 1.212V [Manual Mode] CPU VCCSA Manual Voltage [1.200] DRAM Voltage (CHA, CHB) 1.762V [1.770] DRAM Voltage (CHC, CHD) 1.762V [1.775] CPU PLL Voltage 1.884V [Auto] PCH 1.1v Voltage 1.096V [Auto] VTTDDR Voltage (CHA, CHB) [Auto] VTTDDR Voltage (CHC, CHD) [Auto] CPU Spread Spectrum [Disabled] PCIE Spread Spectrum [Disabled] =============================================================== >CPU Tweakers'Paradise PCIE CLK Skew [Auto] CPU I/O Skew [Auto] CPU I/O Drive Strenght [Auto] =============================================================== >Memory Tweakers'Paradise IMC AB Signal 1 [Auto] IMC AB Signal 2 [Auto] IMC AB Signal 3 [Auto] IMC CD Signal 1 [Auto] IMC CD Signal 2 [Auto] IMC cD Signal 3 [Auto] DRAM CTRL REF Voltage on CHA [Auto] DRAM DATA REF Voltage on CHA [Auto] DRAM CTRL REF Voltage on CHB [Auto] DRAM DATA REF Voltage on CHB [Auto] DRAM CTRL REF Voltage on CHC [Auto] DRAM DATA REF Voltage on CHC [Auto] DRAM CTRL REF Voltage on CHD [Auto] DRAM DATA REF Voltage on CHD [Auto] DRAM Read REF Voltage on CHA [Auto] DRAM Read REF Voltage on CHB [Auto] DRAM Read REF Voltage on CHC [Auto] DRAM Read REF Voltage on CHD [Auto] =============================================================== >PCH Chipset Tweakers'Paradise PCH 1.5V Voltage 1.503V [Auto] PCH 1.1VG [Auto] PCH DMI Strenght [Auto] PCH DMI Skew [Auto] PCH USB Skew [Auto] PCH SATA3 Strenght [Auto] =============================================================== >VGA Tweakers'Paradise VGA1 Core Voltage [Auto] VGA1 Core Voltage Boost [Disabled] VGA1 Memory Voltage [Auto] VGA1 PLL Voltage [Auto] VGA2 Core Voltage [Auto] VGA2 Core Voltage Boost [Disabled] VGA2 Memory Voltage [Auto] VGA2 PLL Voltage [Auto] =============================================================== ***************************ADVANCED**************************** =============================================================== CPU Configuration Intel Adaptive Thermal Monitor [Enabled] Hyper-threading [Enabled] Active Processor Cores [All] Limit CPUID Maximum [Disabled] Execute Disable Bit [Enabled] Hardware Prefetcher [Enabled] Adjacent Cache Line Prefetcher [Enabled] Intel Virtualization Technology [Enabled] >CPU Power Management Configuration CPU Ratio [Auto] Enhanced Intel SpeedStep Technology [Enabled] Turbo Mode [Enabled] CPU C1E [Enabled] CPU C3 Report [Enabled] CPU C6 Report [Enabled] CPU C7 Report [Enabled] =============================================================== System Agent Configuration Inter(R) VT-d [Disabled] PCIE_X16_1 Link Speed [GEN3] PCIE_X16/X8_3 and PCIE_X8_4 Link Speed [GEN3] PCIE_X8_2A and PCIE_X8_2B Link Speed [GEN3] =============================================================== PCH Configuration High Precision Timer [Disabled] =============================================================== If this is not the right place, please move where belongs. Quote
I.M.O.G. Posted April 3, 2012 Posted April 3, 2012 Your digi-vrm settings may not be optimal for air cooling. They are configured for the most part to create maximum heat... That can be ideal if running subzero, but switching frequencies could probably be lowered as well as some other things if you don't have a strong cooling setup on your power section, or LN2/DICE temps crawling across the PCB. I also always disable anything that says "protection"... If you are getting shutdowns when OC'ing, it could be due to something trying to protect you from getting a better score. Or it could be trying to protect you from blowing stuff up, but that sounds pretty boring right. I disable over-current/over-temperature (could fry your board though). You also have speedstep, virtualization, and other power savings type features that are not going to help benching scores. Just my .02 - I didn't go through all the settings, but at a glance these are things that caught my attention. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.