GRIFF

1300Mhz supered )))

Good work !!!!!!

Can you send a photo of the finished work (at akgrif@gmail.com) in particular area RT9238 and photos of the multi-turn trimmer?

I'm not used cpucool in this submission, is the limit of bios options.

Eccellent job TerraRaptor!!!!!!!

4 mhz until the first backup of Christian Ney )))

Vcore=2.15V Vnb=2V Vmem=3.9V

Only VID mod does not have vdroop.

Ok, important notes. Thanks.

For Vnb and Vmem pictures in attached pdfs, for other voltmods i make pictures later.

Vcore=2.16V, Vnb=2V, Vmem=4.1V

14.04.2013 - convert to zip all files 19.01.2014 - add pictures of Vnb mod -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Vnb TUSL2-C voltmod -------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- Voltmods Asus TUSL2-C ita_rus_eng Voltmod Asus TUSL2-C_Vcore_ita_rus_eng.zip

18.01.2014 - add simple vid mod 19.01.2014 - add Ultra-fast and simple mod for VDIMM TUSL2-C, CUSL2 & CUSL2-C. 04.06.2023 - add new link for photos Voltmods Asus CUSL2, CUSL2-C ita_rus_eng Voltmod Asus CUSL2 & CUSL2-C_Vmem.pdf --------------------------------------------------------------------------------------------------------------------------------------------------------------- A very simple VID mod for Asus TUSL2, TUSL2-C, CUSL2, CUSL2-C with HIP6021 pwm controller In this case the values of the voltages in the bios is another plus: * 1.70V = 2.0V (although the datasheet says that must be 0) * 1.75V = 2.1V * 1.80V = 2.2V * 1.85V = 2.3V * 1.90V = 2.4V * 1.95V = 2.5V * 2.00V = 2.6V Simple VID mod --------------------------------------------------------------------------------------------------------------------------------------------------------------------- Ultra-fast and simple mod for VDIMM TUSL2-C, CUSL2 & CUSL2-C. Obtained with the measured real voltage equal to 3.85-3.9V depends on the motherboard and power supply. Mode 'of use: * 1) Insert jumper between contacts 3 and 4 means set 3.6V * 2) start the system * 3) at any time after the first boot screen to enter the second jumper between pins 1 and 2 (as set for 3.4V) * P.S. With two jumpers inserted at the same time the system will not start if the chipset voltage less than 1.95V, tried it on TUSL2 with VNB-C mod that lies above. * With VNB = 2.05V the system also with VDIMM = 3.95V. * END Jumper MEM mod

This is a collection of voltmods for these legendary motherboards made by me.

For mod Vchipset write me on akgrif@gmail.com

GRANDE !!!!!!!!!!!!

Excellent result. Congratulations Gigioracing.

Vcore=2.1V ; Vdimm=3.75V ; Vchipset=2V I am preparing the diagrams and photos for mod Vchipset, Vtt, Vagp, Vcore, Vdimm

I am preparing the diagrams and photos for mod Vchipset, Vtt, Vagp, Vcore, Vdimm

Vcore=2.1V ; Vdimm=3.75V ; Vchipset=2V

Thanks ANANERBE!!!

Yes this is your chip Sebastian. But limited by the chipset((((((((

You will need tweaks use for best result ))))))

Great result with my Ram )))))))))

First backup?