zzolio Posted February 27, 2014 Posted February 27, 2014 it is possible to get OCP disable for chl8318 I can scan my Epower and then change ocp with EVbot and then scan again I'm not sure I can disable the OCP with EVbot I can set it to extreme which is probably the highest that can be set via the I2C bus is there anything else you need? Quote
Guest barbonenet Posted February 27, 2014 Posted February 27, 2014 please elmor add ocp option:D Quote
elmor Posted February 27, 2014 Posted February 27, 2014 I have a test version where you can set the OCP limit very high (can't disable over I2C), but still havn't had it tested. https://www.dropbox.com/s/6d5jaqcv72nr0h3/eVc%20v1b4%20-%20780_ocptest1.exe Use the 780/Ti Lightning profile and you'll find the OCP option at GPU Voltage under More settings. It could be tested by for example setting the limit really low and see if it triggers OCP. Let me know how it goes. Quote
zzolio Posted February 27, 2014 Author Posted February 27, 2014 if i have time i will test this weekend I need to pick up ln2 tomorrow anyway Quote
Guest barbonenet Posted February 27, 2014 Posted February 27, 2014 if i have time i will test this weekendI need to pick up ln2 tomorrow anyway let me know zzolio Quote
Guest barbonenet Posted March 3, 2014 Posted March 3, 2014 for me don't work on epower.....i set 0a and card works:( Quote
elmor Posted March 3, 2014 Posted March 3, 2014 (edited) Can you send me the log file? 0A might be a bugged value, what about 4A? Also what is the result if you go to Menu - Send custom command and enter the following: Address 0x46 Register 0x1D And press Read? Edited March 3, 2014 by elmor Quote
BenchBros Posted March 11, 2014 Posted March 11, 2014 Is voltage adjustment fine on EPOWER? Where are the soldering points? I want to replace evBot - or let me say I dont want to buy one :-p Quote
Guest barbonenet Posted March 11, 2014 Posted March 11, 2014 (edited) work perfectly on epower!!! today i post one picture of pin! or if you want, you can look in last post in How to add unsupported card (i correct pin ) Attenction: SDA and SCL are inverted in this pictures!!! Edited March 11, 2014 by barbonenet Quote
Guest barbonenet Posted March 15, 2014 Posted March 15, 2014 (edited) john tonight i try the ocp on epower! but doesn't work! i use 5850, and in monitoring i read 8A, but if i set 4A for ocp, the card running always! what you need for set it? Edited March 15, 2014 by barbonenet Quote
zzolio Posted March 15, 2014 Author Posted March 15, 2014 sorry I forgot to test the OCP 'll try to remember it tomorrow Quote
zzolio Posted March 16, 2014 Author Posted March 16, 2014 it works it dos shutdown when applying low ocp level like 100A Quote
Guest barbonenet Posted March 16, 2014 Posted March 16, 2014 it works it dos shutdown when applying low ocp level like 100A did you test original ocp in lightining? how many A you read in evc tool? thanks;) Quote
zzolio Posted March 16, 2014 Author Posted March 16, 2014 no you can't read OCP level and I use moa bios Quote
Guest barbonenet Posted March 16, 2014 Posted March 16, 2014 ok, but you have some improvement with increasing ocp? any more mhz? today i don't see your result! Quote
zzolio Posted March 16, 2014 Author Posted March 16, 2014 no just testet with water cooling still waiting for a new ABX with more core clock range Quote
elmor Posted March 17, 2014 Posted March 17, 2014 Looking forward to finding out if it helps, maybe there's a minimum setting so too low values don't work. This is the only way of setting OCP limit that I found so far. Quote
elmor Posted April 3, 2014 Posted April 3, 2014 This version should work fully for OCP, who has time to test? https://www.dropbox.com/s/0078uv0zqm917g6/eVc%20v1b4%20-%20780_ocptest2.exe Quote
Guest barbonenet Posted September 28, 2014 Posted September 28, 2014 elmor i'm trying evc on epower with gtx 980!!! for me ocp doesn't work!!!! can you try other setting please?? Quote
elmor Posted September 29, 2014 Posted September 29, 2014 (edited) I have a confirmed working version, for epower right? Try this: https://www.dropbox.com/s/5cr9em81my6o1ql/eVc%20v1b4%20-%20epower_ocp.exe?dl=0 If applying voltage through eVc, Gamer OCP is the value you want to change. Edited September 29, 2014 by elmor Quote
Guest barbonenet Posted September 29, 2014 Posted September 29, 2014 (edited) I have a confirmed working version, for epower right? Try this: https://www.dropbox.com/s/5cr9em81my6o1ql/eVc%20v1b4%20-%20epower_ocp.exe?dl=0 If applying voltage through eVc, Gamer OCP is the value you want to change. thanks john, i try it today.....and regular ocp what is???? OCP Test in advanced, should be left at 0A???? Gamer OCP work at all setting? if i apply 496A it work? EDIT: i look now it....but i didn't test! can you add again temp of VRM please? thanks Edited September 29, 2014 by barbonenet Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.