Christian Ney Posted February 22, 2011 Share Posted February 22, 2011 (edited) Hi, I cannot go higher than 520 Mhz, I tried a lot of settings, but still cannot pass 520 Mhz. Atm using a Core 2 Duo 6320 Is there some settings that have to be set in order to pass 520 Mhz ? Thx, atm I am a noob on recent hardware for who knows Edited February 23, 2011 by Christian Ney Quote Link to comment Share on other sites More sharing options...
knopflerbruce Posted February 22, 2011 Share Posted February 22, 2011 Maybe I'm a conroe noob, but not all of these are FSB monsters Could just as well be the CPU. What CPu PLL /FSB Termination voltages? Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted February 22, 2011 Author Share Posted February 22, 2011 (edited) pll v: 1.7v temp: 0°C fsb v: 1.6v temp: 1°C Edited February 22, 2011 by Christian Ney Quote Link to comment Share on other sites More sharing options...
Crew Turrican Posted February 22, 2011 Crew Share Posted February 22, 2011 jeez, those are pretty high voltages. maybe your cpu has a fsb wall there. my e6320 also had one, but much lower. Quote Link to comment Share on other sites More sharing options...
TaPaKaH Posted February 22, 2011 Share Posted February 22, 2011 Most likely it's the FSB wall, Conroe chips have that between 450 and 600 on air depending on the chip. In most cases the FSB wall moves when going subzero - ~30MHz gain from air to dryice/singlestage and 50-60MHz gain from air to LN2 Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted February 23, 2011 Author Share Posted February 23, 2011 (edited) haha, I was thinking about a wall or a combination of BIOS settings(damn too much bios settings for this board ), cause it's 100 % stable at this freq, end when I add only 1 more mhz, I have an instant blue screen. So I tried higher voltages(as Karl said, these are high), and still cannot get 521 Mhz. Hum I have to try the 2 other 6320 I have to find if they have this same wall too. Thank you guys for the confirmation. Edited February 23, 2011 by Christian Ney Quote Link to comment Share on other sites More sharing options...
Crew Turrican Posted February 23, 2011 Crew Share Posted February 23, 2011 yeah, just recently i had it with my e6300 as well. all benchmarks could be run between a range of ~10mhz cpu clock. 1mhz higher in fsb and it freezes, regardless of voltage\etc. Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted February 23, 2011 Author Share Posted February 23, 2011 (edited) Damn, I need more chips btw the Pentium 4 530 I told you last day, I tested the 4 chips I have, and the wall is 300 Mhz FSB for two of them and 295 for the 2 others.(or maybe here it's the cpu limit ) Edited February 23, 2011 by Christian Ney Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted February 23, 2011 Author Share Posted February 23, 2011 Seems there is really a wall, I am running everything with stock voltages and the e6320 is @ 3.7 Ghz stable superpi and wprime. lol Quote Link to comment Share on other sites More sharing options...
knopflerbruce Posted February 24, 2011 Share Posted February 24, 2011 jeez, those are pretty high voltages. maybe your cpu has a fsb wall there. my e6320 also had one, but much lower. Is that alot? I ran my Conroes at 2v CPU PLL and 1.7 vFSB, they're still alive (that was on LN2 though). I think they scaled through both up to a certain point, but not that high:p Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted February 24, 2011 Author Share Posted February 24, 2011 yeah, just recently i had it with my e6300 as well. all benchmarks could be run between a range of ~10mhz cpu clock. 1mhz higher in fsb and it freezes, regardless of voltage\etc. LOL, you know what the second e6320 I have.... ... wall is 450 Mhz using same settings as the one with the 520 Mhz wall And both are L645G559 welcome to overclocking world Quote Link to comment Share on other sites More sharing options...
TaPaKaH Posted February 24, 2011 Share Posted February 24, 2011 well, that's why you don't see the low end conroes being benched at 650+ fsb very often ... otherwise it would have been too simple Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted February 24, 2011 Author Share Posted February 24, 2011 Yeah sure, but its still impressive when I have same batchs that are far away regarding the max freq or stability. different batch/stepping is ok, but to see a huge difference with the same batch like 600 mhz it s quite impressive, most of the time I have 10 mhz between double/triple cpu I have. Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted March 5, 2011 Author Share Posted March 5, 2011 (edited) héhé, I just tested the 3rd chip I have... 1st chip : 452 Mhz wall 2nd chip : 520 Mhz wall 3rd chip : boot from bios 565 Mhz ambient air btw Little preview : http://hwbot.org/community/submission/2136040_christian_ney_superpi_core_2_e6320_1.86ghz_13sec_47ms?new=true Edited March 5, 2011 by Christian Ney Quote Link to comment Share on other sites More sharing options...
Crew Turrican Posted March 5, 2011 Crew Share Posted March 5, 2011 good one Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted March 5, 2011 Author Share Posted March 5, 2011 (edited) Tested : Corsaid Dominator GT CMG4GX2M2A1066C5 200 € : 487 Mhz 4-4-4-12 2.6v Kingston HyperX KHX8500D2/1GCL5 20 € : 503 Mhz 4-4-4-12 2.6v GSKILL F2-8500PHU2 2GBHZ 540 € : 625 Mhz 4-4-4-5 2.8v EDIT GSKILL, stable under SuperPi 1M : 4-4-3-3 2.6v @ 630 Mhz Edited March 5, 2011 by Christian Ney Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.