Vertex_FR Posted March 22 Share Posted March 22 7 hours ago, razerware said: hi, I’m using x7r for tachyon. I can boot on 8400 with a die, but cannot boot on 6800@7600 with mdie during my yesterday attempts. is this bios better for adie? Should i use f8 instead? Hello, you should try rdeq1, if i remember correctly it was needed for me on mdie for 7466c32 on Elite AX Quote Link to comment Share on other sites More sharing options...
razerware Posted March 22 Share Posted March 22 9 minutes ago, Vertex_FR said: Hello, you should try rdeq1, if i remember correctly it was needed for me on mdie for 7466c32 on Elite AX what rdeq1 for？stability？ i am using Predator Hermes 24G*2（6800） Quote Link to comment Share on other sites More sharing options...
Vertex_FR Posted March 22 Share Posted March 22 17 minutes ago, razerware said: what rdeq1 for？stability？ i am using Predator Hermes 24G*2（6800） you mean Mdie 24gb ^^' never tested this rev Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 27 Author Share Posted March 27 Old M-Die works also fine with X7P but don’t forget, old M-DIE can’t boot so high on Air. I was able to bench with 14900k up to 7200 1T and 7600 2T Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 21 Share Posted April 21 Hello, someone can help me? Im currently using z790 tachyon x ( X7R BIOS)- 14900KF 98 biscuits 8200 C38-46-46-46 or 8200 C34-46-46-46 error around 2-3 minutes in Karhu. SA 1.24 CPU - 1.4 - 1.45 DRAM - 1.55 / 1.55 rdeq mode 2 + flare mode... Temperature never exceed 30c What can I do to have a daily 8200 ? Quote Link to comment Share on other sites More sharing options...
sergmann Posted April 21 Author Share Posted April 21 your voltages for CPU are to high. Try SA 1.2 / CPU 1,30/1,35 and check if it`s mor stable or not. You can also select directly 8400 profile which is stored in the bios, it works fine as start point Quote Link to comment Share on other sites More sharing options...
freak77power Posted April 21 Share Posted April 21 (edited) 12 hours ago, Lionson said: Hello, someone can help me? Im currently using z790 tachyon x ( X7R BIOS)- 14900KF 98 biscuits 8200 C38-46-46-46 or 8200 C34-46-46-46 error around 2-3 minutes in Karhu. SA 1.24 CPU - 1.4 - 1.45 DRAM - 1.55 / 1.55 rdeq mode 2 + flare mode... Temperature never exceed 30c What can I do to have a daily 8200 ? Your SA is too high for the 14th gen. I have the same board and 14900K. Here are the numbers that are going to work for you SA - 1.14v TX - 1.30v VDD2 - 1.45v Btw. If you don't want to waste your time waiting for Karhu to finish, run Y-cruncher and then play BF2042. If you have a slightly unstable platform you will get BSOD or hard restart in BF2042. Edited April 21 by freak77power Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 21 Share Posted April 21 34 minutes ago, freak77power said: Your SA is too high for the 14th gen. I have the same board and 14900K. Here are the numbers that are going to work for you SA - 1.14v TX - 1.30v VDD2 - 1.45v Btw. If you don't want to waste your time waiting for Karhu to finish, run Y-cruncher and then play BF2042. If you have a slightly unstable platform you will get BSOD or hard restart in BF2042. Yo, I will try this tomorrow,great thanks. I keep 1.55 for dram vdd / vddq ? If it's not stable, can I increase SA ? Or even TX to 1.35? Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 21 Share Posted April 21 (edited) 52 minutes ago, freak77power said: Your SA is too high for the 14th gen. I have the same board and 14900K. Here are the numbers that are going to work for you SA - 1.14v TX - 1.30v VDD2 - 1.45v Btw. If you don't want to waste your time waiting for Karhu to finish, run Y-cruncher and then play BF2042. If you have a slightly unstable platform you will get BSOD or hard restart in BF2042. 8200 C36-48-48 or 8200 C38-46-46 ? Edited April 21 by Lionson Quote Link to comment Share on other sites More sharing options...
freak77power Posted April 22 Share Posted April 22 3 hours ago, Lionson said: Yo, I will try this tomorrow,great thanks. I keep 1.55 for dram vdd / vddq ? If it's not stable, can I increase SA ? Or even TX to 1.35? 1.55 should be good enough. Stay with DDR5 8200 C38 for now. Quote Link to comment Share on other sites More sharing options...
freak77power Posted April 22 Share Posted April 22 3 hours ago, Lionson said: Yo, I will try this tomorrow,great thanks. I keep 1.55 for dram vdd / vddq ? If it's not stable, can I increase SA ? Or even TX to 1.35? If it is unstable keep TX at 1.30. and for SA, start with 1.14 and increase by ten 1.15, 1.16. I bet you will be fine at 1.14. and VDD2 set to 1.45 Quote Link to comment Share on other sites More sharing options...
freak77power Posted April 22 Share Posted April 22 1 minute ago, freak77power said: If it is unstable keep TX at 1.30. and for SA, start with 1.14 and increase by ten 1.15, 1.16. I bet you will be fine at 1.14. and VDD2 set to 1.45 Here is C36 DDR5 8000 which will give you better latency than what you are trying to do with assuming you have a really good cooling for it Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 22 Share Posted April 22 4 hours ago, freak77power said: Here is C36 DDR5 8000 which will give you better latency than what you are trying to do with assuming you have a really good cooling for it Thanks, I will try. Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 23 Share Posted April 23 On 4/21/2024 at 11:07 PM, freak77power said: Your SA is too high for the 14th gen. I have the same board and 14900K. Here are the numbers that are going to work for you SA - 1.14v TX - 1.30v VDD2 - 1.45v Btw. If you don't want to waste your time waiting for Karhu to finish, run Y-cruncher and then play BF2042. If you have a slightly unstable platform you will get BSOD or hard restart in BF2042. Crash after 9 seconds of Karhu. Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 23 Share Posted April 23 (edited) 13 minutes ago, Lionson said: Crash after 9 seconds of Karhu. Increased SA to 1.15 / 1.16 / 1.17 / 1.18 / 1.19 / 1.2 - 1 error detected in 10 seconds. Edited April 23 by Lionson Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 24 Share Posted April 24 On 4/21/2024 at 8:01 PM, sergmann said: your voltages for CPU are to high. Try SA 1.2 / CPU 1,30/1,35 and check if it`s mor stable or not. You can also select directly 8400 profile which is stored in the bios, it works fine as start point Crash after 2sec of karhu Quote Link to comment Share on other sites More sharing options...
PEEQ Posted April 24 Share Posted April 24 Hello,does someone have F3 bios? XOC BIOS dont work with 14900ks whatever I do. Just want to try F3 bios even if its bugged / not enough good;;;;; Quote Link to comment Share on other sites More sharing options...
freak77power Posted April 25 Share Posted April 25 (edited) 16 hours ago, Lionson said: Crash after 2sec of karhu It says VDD2 1.474 however it is set to 1.450v in BIOS. Also, it says 1.155 for SA but it is set in BIOS to 1.14. I use X7o BIOS. Also, make sure you cool that mem well. Every silicon is a bit different but this would be your starting point. I would leave RAM to default XMP profile, 8000 speed. You can tweak it later. Almost forgot, set your timing for RAM -> Flare. Also, leave the CPU clock speed on AUTO. Do not overclock your CPU until you find a stable overclock for memory. I hope this helps. Leave low latency and high bandwidth options to AUTO. You don't need to have it enabled because you will tweak your timings manually later. Edited April 25 by freak77power Quote Link to comment Share on other sites More sharing options...
Lionson Posted April 25 Share Posted April 25 Nothing works, Im gonna rma Quote Link to comment Share on other sites More sharing options...
Zarok77 Posted April 25 Share Posted April 25 3 hours ago, Lionson said: Nothing works, Im gonna rma try 8200 c36-50-12-46-98 for daily. also 1.2v sa cpu 1.42 / 1.38 ram 1.55 / 1.51 assuming you talking about adie.... because if your kit is 48gb, make sure trfc is also set to 700 . good luck, you do not need to rma anything imho 1 Quote Link to comment Share on other sites More sharing options...
sergmann Posted April 25 Author Share Posted April 25 16 hours ago, PEEQ said: Hello,does someone have F3 bios? XOC BIOS dont work with 14900ks whatever I do. Just want to try F3 bios even if its bugged / not enough good;;;;; I have tested on Z790 Tachyon X with X1a, X7p and X7r, everything works fine with 14900ks. Zarok77 is also with 14900ks on his Tachyon without problems. Also on Z790 non X everything is fine with it. If you are on non X board, F3 Bios is pretty old, I would try new bios for KS last one is 2 days old with better support for 14900KS https://www.gigabyte.com/Motherboard/Z790-AORUS-TACHYON-rev-10/support#support-dl-bios official bios versions for Tachyon X https://www.gigabyte.com/Motherboard/Z790-AORUS-TACHYON-X/support#support-dl-bios Quote Link to comment Share on other sites More sharing options...
spit051261 Posted Friday at 07:34 AM Share Posted Friday at 07:34 AM (edited) Tachyon X works fine 😉 CPU was on LN2 but RAM was on air . It will run same speed and timings with CPU on water . https://hwbot.org/submission/5534422_ Edited Friday at 07:36 AM by spit051261 Quote Link to comment Share on other sites More sharing options...
sergmann Posted Friday at 03:04 PM Author Share Posted Friday at 03:04 PM Strong chip👍 Quote Link to comment Share on other sites More sharing options...
sabishiihito Posted Friday at 05:30 PM Share Posted Friday at 05:30 PM No new XOC Bios incoming? Proper biscuits for KS, maybe some 24GB mem profiles? 1 Quote Link to comment Share on other sites More sharing options...
Lionson Posted Saturday at 10:21 PM Share Posted Saturday at 10:21 PM On 4/25/2024 at 2:15 PM, Zarok77 said: try 8200 c36-50-12-46-98 for daily. also 1.2v sa cpu 1.42 / 1.38 ram 1.55 / 1.51 assuming you talking about adie.... because if your kit is 48gb, make sure trfc is also set to 700 . good luck, you do not need to rma anything imho Error at 10s Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.