SF3D

Haha..tempting offers guys

Thanks! I just received unlocked bios, so now 2000MHz is possible, if card can do it Ln2 is always a huge problem in Finland. It cost 9,5€/l so I can not spend it like some others. 400 liters in a week would definitely help me to achieve my goals

steponz.. it was used at 6022MHz There was so little ln2, that I just used very safe settings.

Thanks! I am ok with it, cause I have only this one card ASUS did very good job with these!

Nice to see that this Inflection point pot is making people happy all around the world. Keep up the good work people! This product is made for you and you all are winners

that's exactly the reason why I don't use HT. It does not scale well above 6500. See my multicard 06 where I use ATI cards + 12 threads + 6500+ clocks. CPU score is 13K

Yeah..These have been out in ES form for a while.

No no.. the validation file was done months a go.. with CPU-Z 1.55 and it can not be validatet anymore.

Haha..this benchmark is not for one memory stick, that was what I found out Too bad I can not validate CPU-Z anymore.. I got nice 7071mhz out of this.

You must mean "only" 1.9V

Thanks _mat_! I think MIVE is very good board and very easy to use. I don't know why UD7 behaves that way

Zoro- Yes, I am pretty sure that my eyes does not lie and my fingers set the correct values CPU is still in perfectly good condition.

Sam- It is the cpu clocks which is limiting. I was already doing some higher freq runs, but with lower CPU speed. The score was worse + other issues. So I think with some new CPU I will try to show 1140Mhz+ runs for you Zoro- 1.9 VDDR, 1.25 VCCSA, 1.1 VCCIO, 1.8VCPUPLL, Skew + driving voltage changes. Subtimings tweaked a tiny bit.

Good run with watercooling!

fixed

L040B165 #1781 First tests on air were promising: http://sf3d.pp.fi/images/album/ASUS%20Maximus%20IV%20Extreme%20and%20Sandy%20Bridge/Retail%20sandy%20bridge%202/

http://sf3d.pp.fi/images/album/ASUS%20Maximus%20IV%20Extreme%20and%20Sandy%20Bridge/Retail%20sandy%20bridge/ Check the shots from there

L039B470 s/n 4 last digits 1633 4/8 threads. 5GHz IBT standard x 20 max 5050MHz Vantage CPU test + 3DM11 etc. Aircooling. Tomorrow I will get L040BXXX

It is easier to just hit the clear cmos button in the other side of the board when you see 63. Just let the lights go off and boot immediately. It saves time and works every time and you don't loose any settings, but you will get back to bios. But if you get the board to boot, it will most likely fail during OS load anyway in that case.

SB is funny. When you enable speedstep you will be stuck at code 63. You can get over that by pressing the clear cmos button very quickly in the I/O side of board. After that the board will boot back, so you can get back in to bios. If the board boots for some reason with your overclocked settings you will be stuck at middle of loading OS. If speedstep is disbled I see the same AE code, when it should load the hard drive. So the issues are exactly same as Massman and others said. It might be some bios issue with some turbo ratios. I hope it will be fixed soon. If it is not bios issue and it is mostly related to CPU, then it is quite easy to see what your CPU can do. Have someone found any solution for the issue described above? E: and the board is of course Maximus IV Extreme

Haha! True.. it is a bit lame to break WR's with only aircooling I will try this setup on LN2 for sure and then we will hopefully see some good scores.

You must mean 6K backup? 5K was on air

So it died eventually. Too bad, but let's not cry after it, cause something better is near

Hyvä veto! Sitten vaan uutta ajoa ja kohti kärkeä!

Yes!!!