Jump to content
HWBOT Community Forums
miker2ka

Going for XTU 699 with i3 6100

Recommended Posts

Just got myself a MOCF, and trying to get 699 marks on 6100.

CPU can handle 4000 12-11-11 tight.

But i cannot make it run the multiplier x 37 with 102.80 + bclk.

Except RAM setting i tried :

C-states disabled

Clockgen divider 12

pll ort 32

cold bug killer 1.8

vccpll 2.5

bclk 102.80- 102.93

bios L1.31

Win 10 enterprise 32bit ltsb

Everty time i boot into os the multiplier self adjusts to 35 .

I'm running out of ideas!!

Share this post


Link to post
Share on other sites

If i have formula drive installed when i boot os it resets bclk to 100. If i change bclk from os i get instat crash.

Share this post


Link to post
Share on other sites

Got it to work with another version of formula drive. Now im stuck at 696.

Are the pll ort and divider settings good?

And what microcode is ok to use? Or it doesn't matter?

Share this post


Link to post
Share on other sites

Don't care about CPU multiplier in x35, just use 102,9375 to boot then raise in special AFD to 102,97XX and put x37 multiplier... Rest of the settings are great... You should get 697 with 102,9375 and x37 multiplier...

Share this post


Link to post
Share on other sites

Great thread and help from you guys. Subbed to remember what to do with my i3 6100 :)). I hope the imc is decent.

 

 

Sent from my iPhone using Tapatalk Pro

Share this post


Link to post
Share on other sites

I got 697 on win 10 enterprise ltsb 32. Now i tried pro and i get max 694.. next bclk lvl in afd is 103... and it's unstable.

 

If i get 695 often and 697 rarely am i on the path to 699? Or i shoud get like 697 often to hope for 699?

Edited by miker2ka

Share this post


Link to post
Share on other sites

Think XTU doesn't like bclk 103. I managed to boot but xtu reads 100 C on CPU and the score is bad... arround 200 marks.

Is there a way to put bclk slightly under 103?

Share this post


Link to post
Share on other sites
What do you mean by "special afd"?

 

http://picx.xfastest.com/nickshih/asrock/AFDSetup(v3.0.92.1).rar

 

Boot at 102,9375 from bios and use that AFD to set 102,97XX (The last one before 103)

 

Clockgen divider 12 , pll ort =32 , clockgen voltage 3.6 (safe limit) , cold bug killer 1.8 , vccpll 2.5

 

3866x102,9375 mems 12-12-12-28 220 1T 49/50 6/6 should give you 698 with good OS

Share this post


Link to post
Share on other sites

I can get ram to 12-11-11-28 220 1t. Rtl 50/51 sometimes. Dunno how to set them to be 50/51 every boot

Share this post


Link to post
Share on other sites

@Alan_Alberino, ty for afd.

Should 102.9375 blck with ram 12-11-11-28 220 1T 50/51 7/7 give me 699 eventualy?

I can't get to bclk 102.97, it crashes. Max i can get is 102.95.

And clockgen voltage is clk vdd?

And how can i get ram to boot 50/51 every time? With 102.93 it's a bunny. I managed to boot 50/51 with 102 and raise to 102.93-102.95 with afd

Edited by miker2ka

Share this post


Link to post
Share on other sites

Is there a fancy AFD for big OCF that adjusts between 102.9375 and 103.000? I picked up a 6100, also stuck on 697. Maybe futile on the big board, but I'm learning a lot, thanks to you guys! Good luck miker2ka.

Share this post


Link to post
Share on other sites

The AFD in this post shoud work. But it only worked for me with settings above and microcode 2d. And 698 is preatty rare. I hit it 5 times in about 400 runs.

Share this post


Link to post
Share on other sites

I think the xtu version. Is important as well . Maybe someone can tell which one they used for 699

 

 

Sent from my iPhone using Tapatalk Pro

Share this post


Link to post
Share on other sites

I use 6.0.2.8. Think this is the right one. Maybe is just a matter of pacience. 743 was hit with this version. Maybe someone can tell us about other cpu settings like cstates , speed step, cpu amplitude, slew step or rate. E.g. with c states on i get consistent higher scores.

Edited by miker2ka

Share this post


Link to post
Share on other sites
Over 20x698....

 

Didn't rerun enough ^^ Should be getting constant 697s and 698s with good settings... I also need to infinite rerun, was getting those constant 697s and 698s but didn't rerun enough...

Share this post


Link to post
Share on other sites

Running nuts here... With bllk .97 i get lower scores than .93.

I switched to w8 pro 32 9200 and i can't even hit 698. (And same like w10 ltsb with c-states on i get better scores...)

What m i missing?

Share this post


Link to post
Share on other sites

Got the bunnyer ....... 699.... weeee.

I used XTU 6.0.2.14.

Win 10 32bit N LTSB. (All updates except the one from july 2017)

FCLK 1000 and BCLK 102.95.

C-States enabled.

RAM 12-11-11-28-1 220 50-51/7-7

Microcode 2D

Clockgen divider 12

pll ort 32

cold bug killer 1.8

AFD 3.0.92.1

Bios L1.31

 

vccpll 2.5

 

Thanks to @Alex@ro @mllrkllr88 @Luumi and everyone who posted here.

Edited by miker2ka

Share this post


Link to post
Share on other sites

Settings also works for 743.

For 1043 same settings except speed step (must be on).

All 3 CPUs were run with performance power plan.

 

For 1110 was different:

C-states off

Speed step on

Fclk 400

Bclk 103 if cpu can handle (if not 102.97)

Power plan BALANCED (dunno why but was more consistent)

 

For every CPU you can tweak from regedit:

EnablePrefetcher 1 (default is 3)

I added Enable Superfetch and set value 1(default is 0)

Every 2-3 hours delete content of c:\windows\prefetch and restart

 

As for time needed i got results in :

699 - 30 hours

743 - 8 hours

1043 - 20 minutes (i retested and got another 2 scores 20 min each)

1110 - 3 hours

 

 

1215- coming soon (at least i hope :D)

Edited by miker2ka

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...