reggiesanchez

nice score

I sent in a 5870 lightning, and got back and nvidia 210 with a 5870 lightning sticker on it.

Nice score....... but xp is a MUST for wprime

Nice

I gotta be honest k404 i didnt really need to review these scores a whole lot, they were one run then gold on all scores.

Lol........ Looks like your right, wasn't black but bugged none the less

http://thehdwallpapers.net/nvidia-chip-is-on-fire-wallpapers there ya go, its from the april competition

Finally figured it out had around 4l left so gave it one last try with a different bios. Bios set to 1.65pll Boots at 1.688pll Loads windows@ 1.72pll There is about that much fluctuation in all voltages but I would imagine pll is the culprit.

Your Awsome , thank you

Just rma, a board that's been covered in vasoline is a pain in the ass. What do I do break it so it dosent pass there test only to realize I missed a spot of grease and they decline rma. Or don't break the board and get the same one back., because it boots fine for them. Either way I'm fucked.

Are eveyones voltages .600 above what they should be with s2 BIOS or just this board.

This is what i did today. Pulled down to around -35 and got mem set up. Saved profile tried to make a "safe" profile to boot with, and thats as far as ive got. Been benching for around 31/2 hours now and havent been past -125 one time. Just about every bclk/pll combo and nothing works. About two hours in I realized that every voltage on the board is about .600 above what it is set in bios. Think its about time to accept that this board is a BIG waste of time and money. No matter what settings I use even If im at -50 I cant boot more than 2 or 3 times in a row.

so far with s2 bios cbb/cb @ -125 bios starts acting shitty @ -30 this chip never had a cbb or cb before it met gigabyte

Cry about stuff ..........then wait a few months....... Then cry a little more. http://hwbot.org/community/user/sergiorb#Points

ya was switching between both of them, just not the way christian suggests doing it. also dont think it was a short because it was acting that way as soon as temps got down below -120. Not saying its out of the question but I really doubt. Thanks for S2 link hopefully ill have time to try it tomorrow.

thanks for the links, ill read now. Crazy results with first 10l was benching/booting full pot for maybe 10 min and could not get the board to do it again. @Leegoofd you like ud3h better I had a bad feeling when I bought the ud5h @sin0822 tried bclk 100-109 all same results Do any of you have bios s2 ??

Just "tried" to bench my new ud5 for the first time and it was kind of a nightmare. Hopefully someone can help. Did all of the usual things and everything was going fine. Thought I found a cbb @ -90 which I was kind of bummed about but whatever. After a while I realized that it was not cbb because I pulled the temp all the way down and started full pot benching no problem and the system would restart fine as long as I hit reset and did not freeze. I soon realized that anytime the system fails I need to reset bios in order to pass post again. If I hit the reset button than it will boot right up but if I bsod in windows then it wont boot again. Same thing every time seems like it is booting then right as numbers read 99 it restarts. This just goes on untill I reset cmos again. Any thoughts problem is the same on f5 and f8 bios didnt try any others. This pretty much makes the board unbenchable for me so any help would be great.

god dam, memory is SICK

http://en.wikipedia.org/wiki/Propylene_glycol acetone will also work but it evaporates quickly and is pretty corrosive.

Any word on prizes???

Derp derp

Nice

pretty sick

Sharing cpu in any 3d bench really gives potential for unfair advantage. Cant really think of one where it wont.

Great score...... and GREAT voltmeter.