Leeghoofd
Crew
-
Joined
-
Last visited
Everything posted by Leeghoofd
-
-
-
Sounds interesting Giorgio Great results lads, keep em coming ! Question: How does one enter the inner circle of Petri's summerplace ?
-
Sorry to deviate can anyone test if his stick can run 2933 C11-12-14-40 1T plz ( air plz, no wacky voltages )
-
Switch off your monitor then of it happens
-
also covered the dimm slots ? Any condensation in the slots ?
-
Hardwareheaven is sausage site with a good visual wrap... Similar as with HH's review of the 2933C12's, I don't get Dave's review of the the same G.Skill 2933C12. It clearly shows the gain is not there with single sided MFR rams (also due to the loose tertiaries) versus 1600C9, yet the highly recommended award is given... beats all logic... unless you s*ld **t like Sin explained... then it all becomes clear... Some sites seem to have an obligation that an award must be given for each piece of hardware... even if craptastic
-
-
We demand a livestream !
-
Nice work man, really impressed by the bios on these ASRocks
-
-
-
Jonas is bringing his guitar and will play the entire soundtrack of The Titanic for sure
-
Thx for the support James, Dino and Crusty, it seems it was all due to the Phase control being on AUTO, not about the timings lol.... only posts here at high or extreme preset
-
Will flash back tomorrow Steven, got some pointers from Dino.
-
F5S bassplayer. Well you story is the same as I have on the ASROCK/ASUS board, took me 5 mins to get it dialed in at 2600... similar approach on the GB and it doesn't even post,. LED 15 and then shuts down. Tried for hour snow ot get it working properly at 2600MHz, seems I'm missing something vital for PSC. Weird for me is I can boot straight at 2400 7-11-7 rock stable, then loosen to 8-12-8 and adjust some subs and it doesn't post. Use same settings drop back back to 2400 divider, no more post... till I reset and load the profile...
-
-
XPOWER seems to be shaping up with the latest biosses. Question is the 1.19 the same as the T19 ?
-
working with F5S sir oh mighty Steven. 2600C8 at 1.9Vdimm is a no brainer on the ASRock, sadly similar timings don't post yet on the GB... trying some more tonite
-
Nice work there, crazy sticks ! Is this a straight boot at these clocks Dino or at 100 and then up in winblows ? Struggling atm to get 2600 stable lol
-
Okay thx for the heads up retesting results
-
Nice one ! Well done !
-
Gigabyte has very loose tertiaries at 2933 and above, especially tRDRD and tRWRW are too loose to be efficient. Need to be dialed in manually for better performance. ASRock corrected this for higher efficiency since bios 1.43a. My Xpower doesn't even boot at 2800 with none of my sticks... lots of work required there for the bios team
-
-
My retail CPU which I used for reviewing has degraded 100-150MHz, from 4500MHz fully stable at 1.2Vcore till 4350MHz now at 1.15Vcore. 4500MHz works fine in Wprime as long as no stress is on the IMC. Thus encoding, Cinebench, 3D11 alll crash with101 or 124 error... Adjusting voltages doesn't help, seems IMC is flakey now at higher speeds ... max it was tested on was 2800MHz with 2 x 4GB dimms with voltages (ring, SA,...) on AUTO. Maybe that's where the culprit is on one particular board. Temps were fine, around 80°C max measured by Realtemp. CPU acts in a similar way on 4 boards...