-
Posts
3503 -
Joined
-
Last visited
-
Days Won
35
Content Type
Profiles
Forums
Events
Blogs
Posts posted by l0ud_sil3nc3
-
-
4 hours ago, GTI-R said:
I don't know how to install this thing!
I usually double click the installer and finger blast next, next, next
-
2
-
1
-
-
-
-
-
@Sparky's__AdventureI tried vcore as high as 1.6v and no difference and I see no point in blasting 1.7v since this cpu still hasn't seen any cold yet. It could just be poor cpu silicone or maybe the mobo that's holding the cache back but I have no other point of reference since only OCF is here. I think you might be the only one with a 5g cache air cpu that I have seen with most others topping out at 4.8ish.
I don't think Raptor was slowing anything down except waza taking longer to finish vs ssd life.
And as for dual rank kits, I think am good on those atm since there will be fancy new toys to play with this month.
-
1
-
1
-
-
Nice thread Alex
Tried some low bin DJR on OCF to see how they stack up to good old B-Die. I couldn't get anything over 5200ish to pass GB3 so more than likely IMC limited. Performance seems great and not having to remove any memory is also a huge plus as this seems to benefit quite a few benches.
On this kit 1.86v was the sweet spot for training and higher vdimm yielded little to no gain when raising in os. 1.9v set in bios wouldn't train so not a very voltage tolerant kit.
-
1
-
-
Poozen too strong!
-
Awesome run mllr, 11600k no need when you have good old X299 OCF ;)
-
Congrats!
Hope you have a few moar on that G drive
-
1
-
-
7 hours ago, Sparky's__Adventure said:
Taking a look at your most recent result:
https://hwbot.org/submission/4805185
How come you used 3 cores enabled here instead of 4? I found cores 4 and 5 to be the "most efficient".
Also, have you tried much lower tRAS, like 14? Or tightening other settings (like tRFC or maybe even trying some atypical tertiaries) for shaving off maybe a couple dozen ms. I assume you already have tight AF RTLs because OCF.
Maybe even yeeting vcore to get that 5ghz uncore on true ambient.
https://hwbot.org/submission/4790748
With all those tweaks combined, even if you can't bump mem freq because of IMC limit, I feel you could probably beat my SP32M result. I believe your combined OS efficiency and waza boost are superb.
I used 3c 3t because my strongest core was not 4/5 and settings between both runs were identical except the os having a larger maxmem set on the latter and retiring my Raptor.
tRAS lower than 21 will not pass on my pleb tier dual rank kit and lower tRFC doesn't pass consistently. As for atypical tertiaries I can tell you I'm much looser than what have posted on a number of them. Sometimes tighter doesn't equal faster and most definitely not if you can't finish 32M. RTL game is strong for sure because . . . OCF
I am using 1.5v on an NH-D15 with 75f ambient temp so I don't think there's any gas in the tank in this regard. Cache higher than 48 fails to boot nor have any semblance of stability so mega fail in this dept. I'm also Gear 1 limited (and or memory limited) on this cpu as 3866 can't train here unless I use < 100 bclk so there's no going higher freq wise atm.
-
1
-
1
-
-
Time to drop the hammer!
-
@GTI-Rnice job breaking into the 5:04:xxx's
-
1
-
-
-
Paging @websmile
-
1
-
-
Incredible run Bully!
-
1
-
-
Too stronk!
Best one so far?
-
18 hours ago, ivaneza said:
Great LoVo kit, I guess it can take 2.1+ vdimm
btw what SA and IOmem at 5200?
Well 2.01 makes it all the way through and then hangs on stream triad, so it seems to scale inversely at some point after 1.96v.
SA = 1.55v
IOM = 1.65v
-
1
-
-
On 8/23/2021 at 6:23 AM, GTI-R said:
Thanks for the advice.
But now I can't even boot the BIOS.
OS is also questionable (Windows 7)
I'm trying to avoid clearing CMOS if possible.
MAXMEM is 2500, should I lower it?
IO1.6
I tried SA1.65, but it didn't work.
Maybe the timing is too tight.I would remove some more memory 2.5GB is probably making things much harder to pass. Maybe start at 1-1.5GB and see if you can pass with you current timing set.
Time to clear the CMOS
-
2
-
-
Unbelievable this is still here.
I know many of us are old enough to remember spending $2k on a mainstream cpu for dem goldz and all the boints
ttt
-
2
-
1
-
-
Special LS bin G.Skill memory flying on OC Formula
5200c15 1.96v all air cooled with fairly warm ambient temp. Timings are as set in profile and haven't had a chance to start tightening them up but initial results look great.
Also freshy XP courtesy of @Splave
-
3
-
2
-
-
14 hours ago, GTI-R said:
The OS is booting. But the pi stops after about 3 loops. io mem is 1.65v I've increased SA to about 1.68v.
Try 1.6v IOM and 1.65v SA, should be more than enough for most cpu's.
-
14 minutes ago, GTI-R said:
Difficult to set dual rank.
Unable to complete pi
Need to increase normal IO voltage as well?No need to touch regular IO voltage. Dual rank needs a healthy dose of SA and IO M depending on your cpu and what bench you're running.
-
@Leeghoofd might have something your looking for.
-
Tried out latest 1.27H bios, seems same same to 1.27D which it replaced. The only weird thing I noticed on both bios is that certain dividers are missing or disappear for some reason, namely 3866 and 4133.
On 8/19/2021 at 4:41 PM, websmile said:I found a setting in mem section where you can enable cometlake oc - maybe this can help, I can´t test though
Yup it's at the bottom, saw that but no CML to try with here atm.
-
1
-
ASRock Z590 OC Formula Thread:
in Comet Lake (Z490) & Rocket Lake (Z590) OC
Posted · Edited by l0ud_sil3nc3
@GTI-Rtry this AFD I have attached, it hasn't given me any problems like the 1.8v vdimm upon opening bug you're experiencing.
AFDeeznuts.zip