Mr.Scott Posted June 14, 2015 Posted June 14, 2015 Very nice. Modding my board today. Here's to hoping I can get close to that. Quote
I.nfraR.ed Posted June 14, 2015 Posted June 14, 2015 (edited) I don't see a way for 282 1:1 and tight timings (BH-5) though It's not so easy even with s.939. Will fix windows later, however I think the other board is dead (the one without capacitor between 2 FETs to the mem slots) from the high 3.3V rail. It was behaving the same with just vdimm mod. So maybe it is good to be extra careful if your infinity is the same. Edited June 14, 2015 by I.nfraR.ed Quote
phobosq Posted June 14, 2015 Posted June 14, 2015 Good result, once you get your windows straight it will be hard to beat that result. Quote
Mr.Scott Posted June 14, 2015 Author Posted June 14, 2015 I don't see a way for 282 1:1 and tight timings (BH-5) though It's not so easy even with s.939. Will fix windows later, however I think the other board is dead (the one without capacitor between 2 FETs to the mem slots) from the high 3.3V rail. It was behaving the same with just vdimm mod. So maybe it is good to be extra careful if your infinity is the same. Thanks for the warning. Going to try a different route using a small buck converter to power just the ram right at the slot. Similar to what the OCZ booster did. I've done it before on a NF7, but the DFI is a slightly different animal. Quote
Oj0 Posted June 14, 2015 Posted June 14, 2015 Thanks for the warning. Going to try a different route using a small buck converter to power just the ram right at the slot. Similar to what the OCZ booster did. I've done it before on a NF7, but the DFI is a slightly different animal. Hey Mr.Scott, I don't know why but that OCZ booster doesn't work with ANY DFI board I've tried from nForce 2 all the way to nForce 4 and CFX3200. Quote
Mr.Scott Posted June 14, 2015 Author Posted June 14, 2015 (edited) Hey Mr.Scott, I don't know why but that OCZ booster doesn't work with ANY DFI board I've tried from nForce 2 all the way to nForce 4 and CFX3200. Hey Jon. Long time no see. Yes, I'm aware about the booster. If my little buck converter idea doesn't work, I'l just go with the conventional Vdimm mod. EDIT- No boot with converter. Board still works without it (*whew*). Guess it will be to conventional VR mod. Edited June 14, 2015 by Mr.Scott Quote
I.nfraR.ed Posted June 15, 2015 Posted June 15, 2015 The problem with my Ultra B was that conventional vdimm mod didn't work either. Quote
Mr.Scott Posted June 15, 2015 Author Posted June 15, 2015 The problem with my Ultra B was that conventional vdimm mod didn't work either. Hmmm.....interesting. It worked on my Ultra B, and this Infinity doesn't appear to have anything different other than the obvious stuff. Had to send for more trimmers, I was out. I'll finish the mod this weekend. Hopefully, it'll work. Quote
sotoss Posted June 16, 2015 Posted June 16, 2015 hm nice mod you got there , that lcd shows the load of psu ? Quote
Mr.Scott Posted June 21, 2015 Author Posted June 21, 2015 Vdimm mod on my Infinity worked.................for about 15 minutes. Board is dead. Was running 3.65v I would say anything above 3.5v and you're flirting with disaster. Quote
phobosq Posted June 21, 2015 Posted June 21, 2015 It seems that's a black weekend for DFI boards, I tested my two boards yesterday (LP and Infinity) and both seem to be dead, no boot. They have been lying in the closet for a year and boom, surprise. Quote
ludek Posted June 22, 2015 Posted June 22, 2015 @phobosq - its a shame Scotty tell me what do you think about this deads when big vMEM? It's dead chipset or dead MEM power section? Maybe you just blowen ass of power mosfet?! Mabye "ref dimm" voltages must be ideally half of vMEM ? So what do you think? Quote
I.nfraR.ed Posted June 22, 2015 Posted June 22, 2015 Mine worked at 3.7V VDIMM for some time without problems. And my NF7-S boards have always worked at 3.6 - 3.7V, but I think NF7-S is more reliable than DFI Ultra-B. Quote
Mr.Scott Posted June 22, 2015 Author Posted June 22, 2015 @phobosq - its a shame Scotty tell me what do you think about this deads when big vMEM? It's dead chipset or dead MEM power section? Maybe you just blowen ass of power mosfet?! Mabye "ref dimm" voltages must be ideally half of vMEM ? So what do you think? Blew a mosfet in the Vdimm power section. Should be an easy fix. Makes me feel a little better. Quote
ruggero Posted June 28, 2015 Posted June 28, 2015 high fsb but also high time...are you with cpc off? Quote
I.nfraR.ed Posted June 28, 2015 Posted June 28, 2015 cpc on, cpu on agressive, no wazza, totally broken windows. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.