l0ud_sil3nc3 Posted March 23, 2020 Share Posted March 23, 2020 For sure can change in msconfig, but if you can't find it @GtiJason's method also works. Also try running IOL's as an equal number, it's usually more stable for me unless running the first IOL looser than the second i.e. 50 50 7 6 I've never seen 50 51 6 7, first for me, must be EVGA magic tweak 1 1 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 25, 2020 Author Share Posted March 25, 2020 (edited) https://hwbot.org/submission/4389805 5.52.235, flying with 4800. Hope my 8700k and mem have more in them. Edited April 10, 2020 by Sparky's__Adventure Quote Link to comment Share on other sites More sharing options...
GtiJason Posted March 26, 2020 Share Posted March 26, 2020 (edited) 7 hours ago, Sparky's__Adventure said: https://hwbot.org/submission/4385922_sparkys__adventure_superpi___32m_core_i7_8700k_5min_52sec_828ms?recalculate=true I did it, guys! Edit: PB is now 5.52.516, same mem settings as in this post, just better 16k tuning and more aggressive waza. Looking good man ! Must be nice to have a combo (imc,board,ram) that can do 4133c12-11 1T as well as 4800+ C14-13 2T. I have a somewhat fussy APEX XI with imc on 8700k not much better that I just recently was able to run 4800c14 after trying far far far more kits than I've ever had to bin for a given setup. First kit of BDie I bought from Dec 2015 did 4133c12 straight away 1.885v w/ wazza lol. (Edit, MOCF bios set V so about 1.940-1.950v real) What do you mean by PB ? Edited March 26, 2020 by GtiJason 1 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 26, 2020 Author Share Posted March 26, 2020 (edited) @GtiJasonPB is personal best. 4133 12-11 tight is significantly more difficult to run for me, and even still seems slower. What did you do with your first kit of b-die? Honestly, any a2 kit that can run 4080 12-11 can also run 4800 14-13. It seems to need a decent bit less vdimm than 4133, likely at the expense of IMC voltage. Edited March 26, 2020 by Sparky's__Adventure Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 27, 2020 Share Posted March 27, 2020 Next challenge, 49x102bclk! 1 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 27, 2020 Author Share Posted March 27, 2020 @sergmann That will be very difficult, hopefully single stage can help me out. Do you think I need cold mem or cold imc? Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 27, 2020 Share Posted March 27, 2020 I only use custom watercooling for my 9900ks and the G.Skill are only aircooled ;). Just have to work on Waza, so that the time will be even better an I will get the same time of Rauf Unfortunately, I can`t run HOF-Mem with 4933, otherwise I would test it :(. 1 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 27, 2020 Author Share Posted March 27, 2020 (edited) @sergmannHow much voltage do you need, in terms of io, sa, vdimm, and vtt? Also, what are your rtls/iols? Did you boot 100bclk and raise from there? Edited March 27, 2020 by Sparky's__Adventure Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 27, 2020 Share Posted March 27, 2020 Vdimm 2,095 / VTT -25 / SA 1,425 / IO 1,35 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 27, 2020 Author Share Posted March 27, 2020 @sergmannWhat was needed at just 4800? Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 27, 2020 Share Posted March 27, 2020 4800+ 14-13 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 27, 2020 Author Share Posted March 27, 2020 @sergmann I'll PM you from here. Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 28, 2020 Author Share Posted March 28, 2020 https://hwbot.org/submission/4387710 Got tighter RTLs. I got a 4.000s initial twice but haven't seen it since, any advice? Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 28, 2020 Share Posted March 28, 2020 (edited) ? me too, sometimes I get to see 4.0 but then it gets unstable Edited March 28, 2020 by sergmann 1 Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 29, 2020 Share Posted March 29, 2020 @Sparky's__Adventure For Geek you have to reduce twrrd_dg, for me works much much better 1 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted March 30, 2020 Author Share Posted March 30, 2020 @sergmannCan you boot 4900 ratio? 4800 + bclk seems futile and 4933 is a bit too hard on my mem. Quote Link to comment Share on other sites More sharing options...
sergmann Posted March 30, 2020 Share Posted March 30, 2020 4900 not but 4933 works fine for me with the same settings. SuperPi isn`t stable at the moment. My CPU works fine with 73x10x BCLK, so BCLK is more important for me at the moment 1 Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted April 9, 2020 Author Share Posted April 9, 2020 Expiramenting. All ambient as usual. Ambient 20-25C. Anyone with better mem or imc want to give this a shot? 1 Quote Link to comment Share on other sites More sharing options...
l0ud_sil3nc3 Posted April 9, 2020 Share Posted April 9, 2020 10 minutes ago, Sparky's__Adventure said: Expiramenting. All ambient as usual. Ambient 20-25C. Anyone with better mem or imc want to give this a shot? Wow memory scaling with voltage. Can it run anything or just suicide screen? Also why twcl 15 with cash 14? Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted April 9, 2020 Author Share Posted April 9, 2020 (edited) @l0ud_sil3nc3Can't train twcl 14 for whatever reason. I have seen a few people get twcl 12 working even, somethong just wont work. 4933 14-13 1t has some hope of stability, just a bit too unstable at the moment. I can''t get it to run dual channel yet anyways. 4800 14-12 was tested too, but was still far too unstable. Edited April 9, 2020 by Sparky's__Adventure Quote Link to comment Share on other sites More sharing options...
sergmann Posted April 9, 2020 Share Posted April 9, 2020 With the right mem, the Dark can work well. The only thing that annoys me is that I haven´t found the right settings for HOF A2 Mem jet. G.Skill run perfectly 4 Quote Link to comment Share on other sites More sharing options...
l0ud_sil3nc3 Posted April 12, 2020 Share Posted April 12, 2020 @sergmann looking super strong ? Everything air cooled I assume? What is RTL/IOL on the above run? Quote Link to comment Share on other sites More sharing options...
sergmann Posted April 12, 2020 Share Posted April 12, 2020 @l0ud_sil3nc3 Yeah, with open window :). It was little bit cooler outside at night. Mem was running at 17°C. SPI 58/59/7/7 Geek 60/61/9/9 1 Quote Link to comment Share on other sites More sharing options...
Mahameru Posted April 12, 2020 Share Posted April 12, 2020 2 hours ago, sergmann said: @l0ud_sil3nc3 Yeah, with open window :). It was little bit cooler outside at night. Mem was running at 17°C. SPI 58/59/7/7 Geek 60/61/9/9 Looks solid there... what SA and IO needed? Your RTLS and IOLS are insane.. have you try your stick running at 25-30 Celcius with those setting? Quote Link to comment Share on other sites More sharing options...
SparkysAdventure Posted April 12, 2020 Author Share Posted April 12, 2020 I an run 58/59/6/6 but then I can't bclk up very much. Maybe I should try 58/59/7/7 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.