reggiesanchez Posted July 8, 2012 Share Posted July 8, 2012 Just "tried" to bench my new ud5 for the first time and it was kind of a nightmare. Hopefully someone can help. Did all of the usual things and everything was going fine. Thought I found a cbb @ -90 which I was kind of bummed about but whatever. After a while I realized that it was not cbb because I pulled the temp all the way down and started full pot benching no problem and the system would restart fine as long as I hit reset and did not freeze. I soon realized that anytime the system fails I need to reset bios in order to pass post again. If I hit the reset button than it will boot right up but if I bsod in windows then it wont boot again. Same thing every time seems like it is booting then right as numbers read 99 it restarts. This just goes on untill I reset cmos again. Any thoughts problem is the same on f5 and f8 bios didnt try any others. This pretty much makes the board unbenchable for me so any help would be great. Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted July 8, 2012 Share Posted July 8, 2012 Some reading for you: Gigabyte GA-Z77X-UD5H Overclocking Experience: Tips and Tricks There is a lot of blabla at the beginning, go to half page for the interesting stuff Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted July 8, 2012 Crew Share Posted July 8, 2012 (edited) Some more tips/issues : http://www.madshrimps.be/articles/article/1000309/Gigabyte-Z77-D3H-and-Z77X-UD5H-Reviewed/10#axzz204TRpC5j Best flash Bios S2 was the most hassle free for us... the last bios we used this weekend was horrific... no RAM OCing at all... UD3H rules UD5H Edited July 8, 2012 by Leeghoofd Quote Link to comment Share on other sites More sharing options...
sin0822 Posted July 8, 2012 Share Posted July 8, 2012 id use BIOS F8D also try to use high BCLK like 105-110 Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 8, 2012 Author Share Posted July 8, 2012 thanks for the links, ill read now. Crazy results with first 10l was benching/booting full pot for maybe 10 min and could not get the board to do it again. @Leegoofd you like ud3h better I had a bad feeling when I bought the ud5h @sin0822 tried bclk 100-109 all same results Do any of you have bios s2 ?? Quote Link to comment Share on other sites More sharing options...
sin0822 Posted July 8, 2012 Share Posted July 8, 2012 (edited) it is on TT website: http://forums.tweaktown.com/gigabyte/28441-gigabyte-latest-beta-bios-11.html#post274647 Did you try the backup BIOS? Edited July 11, 2012 by sin0822 Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 9, 2012 Author Share Posted July 9, 2012 it is on TT website: http://forums.tweaktown.com/gigabyte/28441-gigabyte-latest-beta-bios-11.html#post274647 Hey also if something like that happens I would tear down the system and let it dry out. It sounds like a short or something. Did you try the backup BIOS? ya was switching between both of them, just not the way christian suggests doing it. also dont think it was a short because it was acting that way as soon as temps got down below -120. Not saying its out of the question but I really doubt. Thanks for S2 link hopefully ill have time to try it tomorrow. Quote Link to comment Share on other sites More sharing options...
dinos22 Posted July 9, 2012 Share Posted July 9, 2012 watch my video on youtube dinos22 channel some good tips in the thread otherwise (other than goofball j/k ) also not all chips act the same so all these are just rough guides i guess Quote Link to comment Share on other sites More sharing options...
Calathea Posted July 9, 2012 Share Posted July 9, 2012 I have the same problem with my UD3H, bad cbb (tested with 3 cpus) and need to clear cmos after crash. Not a kind board for a bencher. Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted July 9, 2012 Share Posted July 9, 2012 UD3H seems better for cpu clocking and UD5H for memory clocking Quote Link to comment Share on other sites More sharing options...
dinos22 Posted July 9, 2012 Share Posted July 9, 2012 I have the same problem with my UD3H, bad cbb (tested with 3 cpus) and need to clear cmos after crash. Not a kind board for a bencher. are you sure, ive tested a fair few UD3H boards and CPUs and i can get it to do what i want every time once i learn how it behaves. most CPUs CBB at -150C mark or just below, some have no CBB. Like christian discovered you should be using a safe boot profile into windows so if you bomb out most times it will simply just reset and go back into windows (depending on the chip) but if it doesnt turn off, warm up to -145C turn on and it will start up. i rarely have to go to -80 but after a bad crash or if i miss my initial CBB temp mark i would have to go to -80 spend time and learn what it likes and what it doesnt like at the start. this will save you a lot of headaches and LN2 in the long run Quote Link to comment Share on other sites More sharing options...
Calathea Posted July 9, 2012 Share Posted July 9, 2012 I will test tonight with fail safe settings on backup bios. Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 9, 2012 Author Share Posted July 9, 2012 so far with s2 bios cbb/cb @ -125 bios starts acting shitty @ -30 this chip never had a cbb or cb before it met gigabyte Quote Link to comment Share on other sites More sharing options...
sin0822 Posted July 9, 2012 Share Posted July 9, 2012 (edited) that is very odd behavior. Vaseline and di-electric grease are very much alike, they both have di-electric properties which means they do not conduct any electricity, so i doubt that would be causing this issue. I haven't seen this before, but I have seen some other random issues and I have told people that they need RMA. So i would say RMA the motherboard. The voltages being set 0.6v wrong could be an issue with one of the ICs on the board, which would require an RMA, as this is 100% hardware defect in your particular board, not a BIOS problem. Edited July 11, 2012 by sin0822 Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 9, 2012 Author Share Posted July 9, 2012 This is what i did today. Pulled down to around -35 and got mem set up. Saved profile tried to make a "safe" profile to boot with, and thats as far as ive got. Been benching for around 31/2 hours now and havent been past -125 one time. Just about every bclk/pll combo and nothing works. About two hours in I realized that every voltage on the board is about .600 above what it is set in bios. Think its about time to accept that this board is a BIG waste of time and money. No matter what settings I use even If im at -50 I cant boot more than 2 or 3 times in a row. Quote Link to comment Share on other sites More sharing options...
Christian Ney Posted July 9, 2012 Share Posted July 9, 2012 that's very odd, => RMA Quote Link to comment Share on other sites More sharing options...
sin0822 Posted July 9, 2012 Share Posted July 9, 2012 yea i would say RMA, its defective. i have a few UD5Hs and none of that kind of behavior. They all have the same cold behavior, infact all the GB Z77 boards I have tested do, none of them have CBs like that unless the CPU has one. Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 10, 2012 Author Share Posted July 10, 2012 Are eveyones voltages .600 above what they should be with s2 BIOS or just this board. Quote Link to comment Share on other sites More sharing options...
dinos22 Posted July 10, 2012 Share Posted July 10, 2012 RMA it mate, not normal! Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 10, 2012 Author Share Posted July 10, 2012 Just rma, a board that's been covered in vasoline is a pain in the ass. What do I do break it so it dosent pass there test only to realize I missed a spot of grease and they decline rma. Or don't break the board and get the same one back., because it boots fine for them. Either way I'm fucked. Quote Link to comment Share on other sites More sharing options...
dinos22 Posted July 10, 2012 Share Posted July 10, 2012 Pm me ur details, I will tell my contact you are RMAing a board Quote Link to comment Share on other sites More sharing options...
Crew Vivi Posted July 10, 2012 Crew Share Posted July 10, 2012 Pm me ur details, I will tell my contact you are RMAing a board now thats service Quote Link to comment Share on other sites More sharing options...
reggiesanchez Posted July 10, 2012 Author Share Posted July 10, 2012 Pm me ur details, I will tell my contact you are RMAing a board Your Awsome , thank you Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted July 10, 2012 Crew Share Posted July 10, 2012 Your Awsome , thank you Never ever tell that in public... Quote Link to comment Share on other sites More sharing options...
sin0822 Posted July 10, 2012 Share Posted July 10, 2012 now thats service agreed! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.