TASOS
-
Posts
1526 -
Joined
-
Last visited
-
Days Won
37
Content Type
Profiles
Forums
Events
Blogs
Posts posted by TASOS
-
-
In the advanced memory section.
I actually find things easier to navigate and find in classic mode by pressing F2
There is not there.
-
The following memory OC profiles are available:
Where can i find these ?
-
did you install intel Management Engine driver?
You cant drive a car without a steering wheel.
The answer is yes.
-
Chaintech Zenith series 9CJS , eh ?
Not good performers back then , though.
-
Should i also write here , about memory overclocking problems ? or should i write them in sin0822 o/c guide thread ???
Well , long story short , is that (at least my efforts)
Hynix CFR clocks as expected
Samsungs clock a bit lower than usual
PSC is a disaster !!!
I dont have any access to any of those ready-set memory profiles , so the results are based on my own limited knowledge.
-
About the on-board buttons, did you install the OCbut ?
Yes oc button is installed.
There is no responce.
They dont even light up , when pressed.
-
Ahhh.
Also ... i forgot it earlier.
The on-board switches for bclk and multi DONT work.
-
-
Gigabyte Z97X-SOC Force
The good points
Nice looking board !
Well equipped !!
Theoretically very well build in terms of both hardware and software !!!
But ...
As a new product , there are some things that perhaps need minor adjustments ? or bios development ?
I dont really now , that's why i opened this thread.
I run into a few minor problems , and i'm looking for a solution.
A.
I cant operate the board with a pci vga card.
A recent generation of a DX11 HD5450.
The vga is a perfectly working card , tested on an other motherboard.
Whenever i plug it in , an exclamation appears in device manager (pci to pci bridge) driver.
The card doesnt accept any version of AMD drivers (new or old) to be installed.
Tried re-installing system drivers , vga drivers , new windows7 os install ... nothing changed.
Same result on both pci slot's.
B.
Tried an other (pci-e this time) HD4350.
Tested and perfectly working vga.
The system booted the 1st time as a standard vga and after installation of the proposed 13.9 AMD drivers ... BSOD all the way.
Tried older version of drivers , nothing changed.
Tried the first two pci-e slots.
Now i'm working the board with an HD7870 with no problems.
For the record , i had the same results-problems using bios version F5 , X04 , F6.
Open to suggestions.
/
-
He is on a reporting streak , with this benchmark.
There are reported submissions all over the place.
-
This is an O/C guide and i'm looking for some answers about generic matters ? ... do we have a specific thread in this forum ?
About SOC-FORCE model.
-
If I may; a query regarding The DX11 PCI challange;
There is only one PCI ran on that bench ever made. I know PCI cards are not a popular HW to use but I would think that with just under 40,000 benchers there would be more than just one
And that one run is questionable as pointed out by Strunkenbold.
http://hwbot.org/submission/2280939_
Could there have been an error made when it was submitted.
Or am I completely wrong and DX11 can run on a PCI card.
If I am wrong;
Pardon my ignorance
If it is wrong;
Since no submissions have been made yet, change to DX9 or whatever.
The above result is submitted in wrong category.
That card sure is a pci-e version.
There is NO sapphire 5450 pci , with 1GB ram.
and sure doesnt look like a low profile pci card , in the photo.
A result moderator must edit it.
.
-
Two months in a row (February and March) , there is no name for the member of the month.
The problem still exist.
The member of the month is ... nameless !!!
-
I got a nap , waiting for the bench to finish ... lol
-
Thanks
We need a better cpu (imc).
-
All I see so far is that all teams uniformly lose points hour after hour.
Shouldn't the recalculation assign "greater or equal" number of points to every score than it was previously?
That's exactly my thoughts too.
I was expecting to see a raise to our team points ... and till now i see a dive of 7500 points.
Let's wait and see ...
-
Max mem clock on nf2 ... eh ?
I believe it's not only a matter of board and bios ... it seems to be cpu dependant too.
I have different results on the same mobo (epox 8rda3) with different cpu's
-
...but all the memory vendors can do high frequency on this board.
Does this apply to the regular SOC Force also ?
-
Stage 3 , includes Sandy Bridge-E also ?
-
Please read this post
http://forum.hwbot.org/showpost.php?p=313417&postcount=335
I believe it's related ... and perhaps you have more problems than you think.
-
What is going on with HWBOT today ???
I see a new score on my team wall and when i click it ... i see the score of an other member from other team
//
I get into a members wall ... and i see achievements of a totally different member (from an other team)
What is going on ?
edit for pictures
.
-
No ES in competitions.
I didnt refresh the page earlier ... so i didnt see your answer.
Sorry.
-
Hi it ok to run ES CPUs example T2500 ES in SC1 stage5.
Team Cup 2012 and 2013 didnt allow ES.
I guess ... there will be no change in this matter.
-
I have simply run-out of excuses.
I dont know what else to say , to my team members.
This issue has gone too far.
It's been MONTHS.
It should have been , much higher in your priorities !!!
Very disappointed.
Sin's Ultimate GIGABYTE Z97X Overclocking Guide
in Haswell (Z87/Z97) OC
Posted
For persons like me (aka "the retailers")
There is nothing in classic mode
There is nothing in uefi mode
There might be something in ghostbuster mode , but i still havent found the combination keys to enable it.