Jump to content
HWBOT Community Forums

Doug2507

Members
  • Posts

    940
  • Joined

  • Last visited

Everything posted by Doug2507

  1. Still can't check my pts/hardware/subs etc etc. Any chance of looking into this? Be appreciated!
  2. L528B167 (1) VID 1.24 5ghz boot @ 1.405v 5.1ghz boot @ 1.495v CB15 49@1.42v L528B167 (2) VID 1.26 4.9ghz boot @ 1.4v L529B200 VID 1.2v 5ghz boot @ 1.385v 5.1ghz boot @ 1.455v CB15 49@1.385v (Couldn't run 5.0, temp) L532B112 (1) VID 1.2v 5ghz boot @ 1.385v 5.1ghz boot @ 1.44v CB15 49@1.37v, 50@1.46v L532B112 (2) VID 1.22v 5ghz boot @ 1.365v 5.1ghz boot @ 1.455v CB15 4.9@1.345v, 50@1.45v (only after delid for x50)
  3. Pepiinorang, are you soldering onto the ST/ST V6 read points before coating the board for cold?
  4. Doug2507

    Small Dewar (UK)

    Looking for a 10-15L dewar, it'll need shipping to Aberdeen (UK) unless reasonably local.
  5. Few 6700k's turned up today, should get them checked on a water loop today / tomorrow (will post once done) and cold next week. (1st time freezing! ) L328B167 x2 L329B200 x1 L332B112 x2 From what i can gather they really need a delid to fully test on LN2. Would testing them before this still give a good indication of potential or will i be thermally limited way to early to tell? Not sure i want to delid every chip but i guess delid/paste/seal will be beneficial for new owners anyway...
  6. Own profile pages won't show correctly. (points/subs etc etc). EDIT: "Error message: org.apache.torque.NoRowsException: Failed to select a row." Unable to check points, most frustrating. Tried viewing logged out and same deal. Also had a problem for longer than i can remember of when checking out someones hardware subs, say a cpu for example with more than 20 subs, when moving onto the second page of results it always throws an error.
  7. Doug2507

    KPE F1 Dragon

    Spot on. Bit the bullet and ordered mobo new but I'll shout him on the pot. ðŸ‘
  8. Own profile pages won't show correctly. (points/subs etc etc). EDIT: "Error message: org.apache.torque.NoRowsException: Failed to select a row."
  9. Doug2507

    M6E / Z87 MPower

    Having a sort through everything thats been in the wardrobe the past year or so, couple of Z87 boards i've got spare and no use for. M6E. iirc i got this from XA with proven non chip killer record. Previously prepped for cold but mostly cleaned up. MSI Z87 MPower. Never been on cold. Used this when i had my good 4770k before i screwed the nuts off it and sent it to silicon heaven. (RIP L310!) Both sold as seen, i.e, no accessories etc. I've got all the MPower stuff though so if someone desperately wants i can go dig it all out. (box included). Not sure what the going rate these days is so £80 for the M6 and £50 for the MPower. (+ postage). If thats way off the mark someone let me know!
  10. Doug2507

    [FS] Two Tek-9 FAT

    NVM. (just realised i've still got one!)
  11. Doug2507

    4x4gb 2400+ DDR3

    Looking for a set of quad for a daily rig. Not fussed if it's sammys or hynix etc. Looking for 2400c9/2666c10/2800c11/3000c12. Any from these will do as they'll be run pretty much stock, maybe tightened down a little. PM me with what you've got.
  12. Perfect, i shall give him a shout. Yep, saw that one. Asking to much for me.
×
×
  • Create New...