jiccman1965 Posted January 17, 2020 Share Posted January 17, 2020 Bit hard to run this bench unless you have a mass amount of ram tried to run with 32gig said it was not enought. Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted January 17, 2020 Crew Share Posted January 17, 2020 Without maxmem? Quote Link to comment Share on other sites More sharing options...
yosarianilives Posted January 18, 2020 Share Posted January 18, 2020 5 hours ago, Leeghoofd said: Without maxmem? 6 hours ago, jiccman1965 said: Bit hard to run this bench unless you have a mass amount of ram tried to run with 32gig said it was not enought. Ycruncher 10b uses over 40gb of ram, so on most platforms you need to use a 64gb kit, 48gb of ram is probably the minimum. If you don't have enough ram you can configure it to use disk either through a page file or the better way swap mode. http://www.numberworld.org/y-cruncher/guides/swapmode.html The nice thing about swap mode is you don't need to configure a proper raid, just point it to the drives you want to use and it will do its own sort of raid without needing to overwrite other data you might have on your drives. 1 Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted January 18, 2020 Crew Share Posted January 18, 2020 I've seen 32GBs subs, but if you want we can lower it Quote Link to comment Share on other sites More sharing options...
Crew Sweet Posted January 18, 2020 Crew Share Posted January 18, 2020 Yes please, thats bench is imposible -10pb-, and i hate it...1pb is possible to change ? Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted January 18, 2020 Crew Share Posted January 18, 2020 already done, advised the french guy we lowered the benchmark Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted February 1, 2020 Crew Share Posted February 1, 2020 !!!!!Due to multiplier detection error , Open Hardware Monitor will no longer be allowed for future submissions. Frequency (and temperature) Monitoring via HWinfo32/64 and or Benchmate!!! Quote Link to comment Share on other sites More sharing options...
Max-Hardware_Numb3rs Posted February 23, 2020 Share Posted February 23, 2020 I've noticed that Parallel PI is kinda super random, may I ask you why it has been chosen? To me it looks like more a lucky run farming than a "optimize your platform" type of benchmark, am I wrong? Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted February 23, 2020 Crew Share Posted February 23, 2020 just to give it a spin, but it it will be removed from the benchmark list after these challengers Quote Link to comment Share on other sites More sharing options...
Max-Hardware_Numb3rs Posted February 23, 2020 Share Posted February 23, 2020 2 minutes ago, Leeghoofd said: just to give it a spin, but it it will be removed from the benchmark list after these challengers make sense... I just saw my ycruncher sub does't appear in the competition anymore, bug or something wrong with the sub? Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted February 23, 2020 Crew Share Posted February 23, 2020 well let's do a small calculation on that one: Y-cruncher says it finished at 14 past the hour Your screenshot is made at 30 past the hour and HWinfo was running for 10 minutes, so I suppose HWinfo was NOT running during the run as you fired it up at 20 past the hour correct ? Quote Link to comment Share on other sites More sharing options...
Max-Hardware_Numb3rs Posted February 23, 2020 Share Posted February 23, 2020 45 minutes ago, Leeghoofd said: well let's do a small calculation on that one: Y-cruncher says it finished at 14 past the hour Your screenshot is made at 30 past the hour and HWinfo was running for 10 minutes, so I suppose HWinfo was NOT running during the run as you fired it up at 20 past the hour correct ? That's weird, since I usually set the windows like you see in the screenshot and I do the runs only after that, but if the issue is this, no problem, the bios profile is saved and I'm sure that I can replicate it, or even get it better since i was 60mhz lower than the limit, not that the frequency matters much here, it's all on the ram tuning. Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted February 23, 2020 Crew Share Posted February 23, 2020 well it was only you and some other user that had these discrepancies... Quote Link to comment Share on other sites More sharing options...
Max-Hardware_Numb3rs Posted February 23, 2020 Share Posted February 23, 2020 6 minutes ago, Leeghoofd said: well it was only you and some other user that had these discrepancies... I'm trying to understand where the discrepancy is coming from but I'm getting my brain fried over this, so better to use that time to bench it again Quote Link to comment Share on other sites More sharing options...
Max-Hardware_Numb3rs Posted February 25, 2020 Share Posted February 25, 2020 Here you go: https://hwbot.org/submission/4362768_hardware_numb3rs_y_cruncher___pi_1b_ryzen_7_3800x_38sec_473ms?recalculate=true Took me 8 minutes, almost the same score as the other, and I may improve it tomorrow, I never cheated in my life and never will. Quote Link to comment Share on other sites More sharing options...
marco.is.not.80 Posted February 27, 2020 Share Posted February 27, 2020 Who said anything about cheating? Running or not running hwinfo isn't going to change your scores. Leeg is making sure you follow the rules. A runner who has a false start of the line isn't cheating. Too many false starts and they will get disqualified. The fact that you are claiming to never cheat is by far a much more suspicious item of interest than if you ran hwinfo after the benchmark rather than before... Quote Link to comment Share on other sites More sharing options...
marco.is.not.80 Posted February 27, 2020 Share Posted February 27, 2020 Well guys, I gave it my all but can't solve the the puzzle behind a couple of these benchmarks. Still got lots to learn but by far the best part of this competition was getting my hands dirty with a new platform (AMD) and by the looks of how things are going in CPU land it looks like there will be lots of AMD in my future, too :-) Quote Link to comment Share on other sites More sharing options...
Alpi Posted February 28, 2020 Share Posted February 28, 2020 (edited) Congrats guys ! I want to thank for the work for all Hwbot staff and also all of You guys to been part of this nice round ! Had good time and had fun with some pretty new benchmarks for me. Thank You once and see You in the next round ! Edited March 1, 2020 by Alpi Quote Link to comment Share on other sites More sharing options...
Crew Leeghoofd Posted March 8, 2020 Crew Share Posted March 8, 2020 All scores are moderated, putting up a bunch of posts at HWBot's Facebook page, if you see your setup pass by, plz tag !!! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.