Jump to content
HWBOT Community Forums

Recommended Posts

  • Replies 284
  • Created
  • Last Reply

Top Posters In This Topic

Posted

Any hope for Gigabyte GA-Z77MX-D3H ?? I am experiencing ~10% lower performance in WinRar & PCMark7, with i3-3225 Ivy Bridge compared to the 200mhz slower i3-2100 Sandy Bridge..

Posted
Posted
Y U No Have Mpower Bios ? :D

 

E7751IMS.H10 ==> E7751IMS.H24

 

01. Modify some string.

02. Fix Ipv6 function fail issue.

03. Fix some items of CPU Features form show error when load defalut.

04. Add'Win 8 Configuration' item.

05. Enable Secure Flash function.

06. Fixed using AFU3.03RC02 to Flash BIOS error.

07. Support check GOP driver in external VGA card

08. Fix some item can not change value.

09. Fix DRAM frequency incorrect issue when use Patriot PV316G213C1K memory and XMP is enabled.

10. Support MSI Fast Boot.

11. Fix system hang on 0x55 issue when use Team Team-Elite-1866 memory.

12. Fix system hang on 0x55 issue when use SPD 800MHz memory and Sandy Bridge CPU.

13. Add WHCK UEFI GOP TEST fail solution.

14. Fix item "Internel PLL Overvoltage" always Enable when over clock cpu ratio.

15. remove WHCK UEFI GOP TEST fail solution.

16. Set item "Intel C-State" to enabled when use some special cpus

(such as i5-3475s which oc ability are limited) to over clock

cpu ratio to the ratio higher than the ratio 4 cores can reach

at the same time.

17. Fix item "Adjust CPU Ratio" show error when adjust cpu ratio.

18. Fix the issue that BCLK can not fix at 100.5 MHz after clear CMOS.

19. Fix windows boot manager boot sequence show error issue when load default after.

20. Fix can't adjust CPU voltage over 1.53V issue.

21. Remove Secure Flash function.

22. Remove solution:Fix TPM ID issue.

23. Remove pop box of 'cpu ratio'item.

24. Fix oc profile fail.

26. Add OC Retry Counter Item.

27. Add code for MSI Fast Boot.

28. Next boot after AC power loss run normal boot when fast boot enabled.

29. Support check GOP driver in external VGA card when fast boot enabled.

30. Modify 'Win 8 Configuration' to 'Windows 8 Configuration'

31. Add solution:Realtek LAN WHCK-Debug Capability Test fail when memory > 2G.

32. Improve system stability when use AVEXIR AVD3U26661104G-4CM memory and XMP is enabled.

 

 

E7751IMS.H30 ==> E7751IMS.H41

 

01. Fix can not adjust cpu ratio when item "Hyper-threading" set to Disabled and item "Active Processor Cores" set to 1.

02. Adjust CPU Ratio keyin function.

03. Add win8 gop solution.

 

E7751IMS.H41 ==> E7751IMS.H42

 

01. Update the CPU Micro Code M12306A9(015).

02. Fix UpdateBiosAndME function issue.

03. Fix Possible Black Screen issues with GOP Driver.

04. Fix Avexir 2400(patched before) S3 wakeup failed.

05. Update Realtek uefi driver.

06. Update CryptoPkg Module 010.

07. Fix Winxp 64bit S4 error issue.

08. Update Intel Ivy CPU GOP ivy_30131013T01.

09. Fix post code show error issue..

 

 

 

E7751IMS.H42 ==> E7751IMS.H43

 

01. Fix WIN7 64 bit os S4 resume show error message issue.

02. Update ME8.1 1318.

03. Fix System cannot Enter windows 7 most of the time and will just show the message no bootable device found.

 

 

E7751IMS.H43 ==> E7751IMS.H44

 

01. Update Post Time Tuning module 12.

02. Fix it cannot finish Windows 7/8 UEFI Installation When you set the bios boot sequence to SATA HDD as 1st Boot and DVD ROM as 2nd boot and save and exit, then Press F11 to select UEFI DVD to Install.

03. Fixed it will hang 0xAD when use Non-GOP card and enable WIN8.

 

 

E7751IMS.H44 ==> E7751IMS.H45

 

01. Add the solution When you plug DVDROM as SATA 1 and plug SATA HDD as SATA 2 then system cannot Enter windows 7 Legacy OS after system restart from E7751IMS.H43.

02. Remove solution Fix it cannot finish Windows 7/8 UEFI Installation When you set the bios boot sequence to SATA HDD as 1st Boot and DVD ROM as 2nd boot and save and exit, then Press F11 to select UEFI DVD to Install.

03. Add some Multi-Lauguage about fastboot.

04. Change "Boot option filter" to "UEFI and Legacy" when Win7 mode.

05. Fix it cannot enter UEFI Windows after restart OS when set admin Password.

06. Fine tune advanced timing(TWRDRDD) for memory frequency >= 2600Mhz.

 

 

E7751IMS.H45 ==> E7751IMS.H47

 

 

01.Fix issue:Wakeup from S4 failed under Windows7 UEFI mode if you set Administrator password and set the Password check to ¡°BOOT¡±.

01. Fixed "Output Select"item can not working correct.

02. Remove "Press <DEL> or <F2> to enter setup." from post.

 

 

E7751IMS.H47 ==> E7751IMS.H51

 

1. Fixed compatibility issue with Roccat Isku keyboards not usable before OS.

 

+ more unknown for now.

Posted

 

 

i did that one and now i cant get my memory above 1866 (thats its standard, the max i can is 1800) before it was working fine.

and my cpu oc'ing is totally f***

can i flash it back to the previous one ?

  • Crew
Posted

principle is the same, just rename the bios file, put USB stick in the white ROG USB port. Then press the ROG button till it flashes. If it stops after a while the flash is done... excellent tool...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...