Jump to content
HWBOT Community Forums

pepinorang

Members
  • Posts

    251
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by pepinorang

  1. No it's not. I can make a table for ASUS/ASROCK/MSI if it's ok with Nick.
  2. Usually Clear CMOS after failed OC is needed in order to reset Intel ME. Either it is your OC that is failing due to too low vCore, or you could also have the same issue than Joe90br and your Intel ME might be broken. Only advice I can give is to try to increase voltage back to 1.35v or to flash your BIOS several times until it works... Anyway guys, please do note that Non-K OC is not officialy supported and will never be. I have personally tried the BIOS listed in this thread and they work without major issues, so I'm not going to spend anymore time on this, you have to figure out yourself.
  3. Your ME is probably broken, try to flash BIOS with M-FLASH and/or FPT several times until it works.
  4. It boots easily just by setting 12-12-12-28-220-1T and left the rest auto. I'll say this once again: You CAN'T compare memory OC on Mini-ITX/2 DIMM boards with ATX T-Topology, they are worlds appart! A fair comparison would be XPOWER vs M8E vs OCF vs SOC Force or M8I vs MOCF vs Z170I GAMING PRO And has been done more than once: Benchbros also recently posted several results on XPOWER with B-DIE: http://hwbot.org/submission/3191899_benchbros_cinebench___r11.5_core_i7_6700k_15.75_points http://hwbot.org/submission/3191903_benchbros_geekbench3___multi_core_core_i7_6700k_27601_points http://hwbot.org/submission/3191901_benchbros_cinebench___r15_core_i7_6700k_1421_cb
  5. No it's not stupid and actually interesting. As far as I know, there is only two ways to apply CPU ST V6/PLL Termination voltage before post in order to lower CBB on Skylake: A) Embedded Controler B) Increase stock voltage by hardware As far as I know, only one vendor use the solution A (MSI has an EC but it's used for different purposes). MSI had an LN2 jumper that use solution B (JLN1, near debug LED). However, due to differences in PCH quality between pre-launch and post-launch, we stopped using this solution because ~90% of PCH chips produced post-launch can't handle the increase in voltage needed to lower CBB and will refuse to boot when JLN1 is shorted. Thus, CBB on MSI is now the same than other vendors which don't use solution A/B, unless you have an old sample or you binned boards to find a PCH that can handle said voltage increase.
  6. Well done mate, keep pushing like this and I might have a surprise for you soon
  7. My bad, I didn't post the link http://hwbot.org/submission/3188701_the_overclocking_knights_superpi___32m_core_i7_6700k_5min_58sec_562ms?recalculate=true
  8. It has ALWAYS been like that guys, YOU just don't try and blindly follow the rest of the crowd! Just look at the BIOS version (130) it's bunnying oooooold! So far best 32M/XTU aircooled results I have seen on MSI are: Z170A XPOWER GAMING TE + E-DIE = 4000 12-18-18 Z170A XPOWER GAMING TE + B-DIE = 4000 12-12-12 / 3960 12-11-11 Z170I GAMING PRO + E-DIE = 4133 12-19-19 Z170I GAMING PRO + B-DIE = 4133 12-12-12 Also go look at the memory QVL of each vendors, MSI has the BEST memory compatibility on Z170 & X99, no matter the board you compare.
  9. You can already use latest official MP BIOS. When used with Non-K CPU it will display an hidden option that when enabled will allow Non-K CPU OC.
  10. Some guys already know about that for a while already but I figured I would post this here as well. HOW-TO run FULL pot on MSI: - Follow Dancop's guide for prepartion and handling: http://forum.hwbot.org/showthread.php?t=154112 - Use PCH slot (in HOT V2 BIOS there is a bug that disable PCH slot when onboard LAN is disabled so don't forget to enable LAN after loading LN2 profile or you will get D6 post code, I'll have this fixed asap) Depending on CPU you will need: - Between 1.7v~2.4v CPU PLL - Between 1.7v~2.78v CPU PLL OC Verified on ~10 CPUs with XA, Dancop, Orion24, Zzolio, Wizerty and Bullshooter, all CPUs were running full pot with no issues with the right settings. I'll be back soon with settings to run full pot on CPU PCI-E slots.
  11. No B-DIE on hand sadly... A bit better efficiency, still have a lot of work to do on the subtimings. Hopefully my girlfriend will let me improve this in between her TV series episodes!
  12. Be happy that anything is happening really, it's most likely last year... Also last year MOA was only an online competition to win a trip for Computex, at least this year live event with cash prize is back, even if it is not worldwide.
  13. Out of curiosity I played a bit with my Mini-ITX gaming rig at home, setup is: MSI Z170I GAMING PRO 2x4GB G.SKILL TRIDENT Z 3866 (Samsung E-DIE) @4133 12-19-19-28-300-1T i7-6700K ES Cooler Master Seidon 120XL AIO Watercooler Non-ACPI BIOS, LSC1, Wazza, Maxmem 600, fresh untrimmed & untweaked FR XP SP3. Still have to work on efficiency but I'm quite happy with that cheap gaming board.
  14. FIY, Non-K OC will still work in the future on MSI motherboards and there won't be special BIOS needed anymore. When BIOS will detect Non-K CPU it use old microcode and display an option to enable Non-K OC. Will let you know which BIOS versions exactly asap.
  15. BETA BIOS 161 uploaded in first page, it improve Memory compatibility. We are preparing a new XOC BIOS asap, including some new memory presets and full ACPI compatibility for XP! :woot:
  16. Yours is different, as you said you can NEVER boot and it's not the same board neither.
  17. I tested this one, again without issue... See screenshots I posted. What's the post codes ? Anyway, I'm going to re-test all 17 supported boards with retail i3 6320, but I'm convinced I'm just wasting my time...
×
×
  • Create New...