Crew Leeghoofd Posted September 29, 2014 Crew Share Posted September 29, 2014 Darn Max, do you give also special tutoring lessons to the elderly ? 1 Quote Link to comment Share on other sites More sharing options...
nedernakker Posted September 29, 2014 Share Posted September 29, 2014 5.5 GHz Max? awesome... How did you tune the voltage transponder variable? Did you use a positive offset voltage or something else? Quote Link to comment Share on other sites More sharing options...
MaxOCer Posted September 29, 2014 Share Posted September 29, 2014 Connected the other 2 sets of pad locations plus this one to on board POS cap    Still waiting to hear back from HQ if we can release the full mod Quote Link to comment Share on other sites More sharing options...
der8auer Posted September 29, 2014 Share Posted September 29, 2014 Quote Link to comment Share on other sites More sharing options...
sin0822 Posted October 7, 2014 Share Posted October 7, 2014 Is there any reason a simple linear regulator with adjustable output would not work for providing this additional voltage? G-powerboard seems like overkill for providing a few tens milliamps. Â U know I was looking into this, if you have a dead mobo around they have tons of linear regulators on them, usually there is one powering the CPU PWM and its easy to extract since there aren't many components around it usually and some datasheets have typical circuits you can build with equations for controlling the output. I also have a circuit development device that has multiple low voltage adjustable dc power supplies on it, however the current is too low, on those you could use an amplifier and boost the current output. My only concern is how dirty the power could be going in and how much it matters in this case. Â this is one linear regulator i was looking into: http://www.xdevs.com/pdf/DCDC/uP7704.pdf Quote Link to comment Share on other sites More sharing options...
dinos22 Posted October 7, 2014 Share Posted October 7, 2014 haha Max is legit man, legit Quote Link to comment Share on other sites More sharing options...
Zeed Posted October 10, 2014 Share Posted October 10, 2014 DER8AUER any update about adapter ?? Quote Link to comment Share on other sites More sharing options...
der8auer Posted October 10, 2014 Share Posted October 10, 2014 Still waiting for a prototype. Seems to take a bit Quote Link to comment Share on other sites More sharing options...
Zeed Posted October 13, 2014 Share Posted October 13, 2014 Longer than i would expect hehe First time since duron 700 or so i went with different MB than Asus and well should have went Asus btw. Shame i never bothered to make proper profile on HWbot since overclocking since 286sx times. Quote Link to comment Share on other sites More sharing options...
Schmuckley Posted October 14, 2014 Share Posted October 14, 2014 I see what you did there  Quote Link to comment Share on other sites More sharing options...
sin0822 Posted October 22, 2014 Share Posted October 22, 2014 Connected the other 2 sets of pad locations plus this one to on board POS cap   Still waiting to hear back from HQ if we can release the full mod  any updates? Quote Link to comment Share on other sites More sharing options...
Massman Posted October 22, 2014 Author Share Posted October 22, 2014 Longer than i would expect hehe First time since duron 700 or so i went with different MB than Asus and well should have went Asus btw. Shame i never bothered to make proper profile on HWbot since overclocking since 286sx times. Â It's never too late http://hwbot.org/benchmark/superpi_-_1m/rankings?hardwareTypeId=processor_2082&cores=1#start=0#interval=20#familyId=232 Â Quote Link to comment Share on other sites More sharing options...
der8auer Posted October 22, 2014 Share Posted October 22, 2014 BTW if you guys don't want to use epower you can always just hook the mod up to a different voltage. VDIMM is usually pretty good because you can use ~1,25 Volt to boot but raise up to 1,7 Volt which is exactly what you need. 1 Quote Link to comment Share on other sites More sharing options...
der8auer Posted October 24, 2014 Share Posted October 24, 2014 So the lazy mod helped vivi to even go to 4500 MHz on cache. Using MSI X99S MPOWER. Good work man! Â http://hwbot.org/submission/2657726_vivi_cinebench_r15_core_i7_5960x_2180_cb Quote Link to comment Share on other sites More sharing options...
Doc.Brown Posted October 29, 2014 Share Posted October 29, 2014 Tested lazy mod three times with different size of solder and it never works on my 5820K ES with SOC Force Rev1.0,first boot after soldering always failed(don't remenber the post code) but second/next boots were goods and when I unmount CPU the solder seems to had melt again Quote Link to comment Share on other sites More sharing options...
Splave Posted October 29, 2014 Share Posted October 29, 2014 can we get a better picture of the advanced mod? Is it the lazy mod then add a wire to both pads? Quote Link to comment Share on other sites More sharing options...
horgantm Posted November 2, 2014 Share Posted November 2, 2014 so all that is required is to have those 2 pins on the cpu bridged, dont need to mod mobo right? So just bridge em and stick it back in and hope for the best? glad I got a ESD safe soldering gun, I have done a lot of soldering on small soundboards so this should be do able. Are there adapters planned so no soldering is required? thanks Quote Link to comment Share on other sites More sharing options...
der8auer Posted November 2, 2014 Share Posted November 2, 2014 Yea just bridge. Nothing else is needed. No mods on the mainboard. Â The first adapter I tried had a bad connection and the system froze randomly. Still trying to get a proper solution. Quote Link to comment Share on other sites More sharing options...
Zeed Posted November 4, 2014 Share Posted November 4, 2014 Thanks for update. So its going somewhere Quote Link to comment Share on other sites More sharing options...
sin0822 Posted November 7, 2014 Share Posted November 7, 2014 Tested lazy mod three times with different size of solder and it never works on my 5820K ES with SOC Force Rev1.0,first boot after soldering always failed(don't remenber the post code) but second/next boots were goods and when I unmount CPU the solder seems to had melt again  interesting maybe its different for the 6-core CPUs. Quote Link to comment Share on other sites More sharing options...
Splave Posted December 2, 2014 Share Posted December 2, 2014 works on the ASRock x99 OCF  x41 with EZ mod x46 with Hard mod 1.60v Epower           Thanks for sharing the mod! Quote Link to comment Share on other sites More sharing options...
horgantm Posted December 18, 2014 Share Posted December 18, 2014 if I connect the 2 pins with 30awg wire, or event a 5mm accent leg (the little sticks that poke out) like this, would that be too thick that it would not allow the cpu to sit correctly? Is it best just to connect the 2 pins with solder itself, and bridge the pads that way? Â BTW anyone make a converter so us poor souls without OC socket dont have to do this? Quote Link to comment Share on other sites More sharing options...
Eddy2317 Posted December 19, 2014 Share Posted December 19, 2014 interesting maybe its different for the 6-core CPUs.  i would not assume that, because of the asus oc socket, but i might be wrong  my i7 5930k is on its way, but i wont try...overclocking noob Quote Link to comment Share on other sites More sharing options...
giorgioprimo Posted January 5, 2015 Share Posted January 5, 2015 Â Â did the lazy mod . mobo asrock x99 formula cpu RETAIL Â Didn't get any improvement on air. SAme wall as before........ Â Anybody can confirm that used the mod on retail cpu and get improvement on air ? Quote Link to comment Share on other sites More sharing options...
Zeed Posted January 6, 2015 Share Posted January 6, 2015 der8auer any news on cpu pad ?? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.