Smoke Posted July 23, 2015 Share Posted July 23, 2015 Elmor, can you add this? Device scan 23.07.2015 23:28:05: 0x06 IR3595A same like used Galaxy HOF Powerboard Quote Link to comment Share on other sites More sharing options...
elmor Posted July 27, 2015 Author Share Posted July 27, 2015 Hey Smoke, I'm on it just need a bit of time to get data on how this device works. Don't have any unit with it to try right now. Quote Link to comment Share on other sites More sharing options...
xxbassplayerxx Posted July 28, 2015 Share Posted July 28, 2015 Same controller with GTX 980 TI K|NGP|N. Lots of info here. My card arrived today so I should be able to get the dump for you this evening. Quote Link to comment Share on other sites More sharing options...
elmor Posted August 2, 2015 Author Share Posted August 2, 2015 Hey, try this: https://www.dropbox.com/s/x1pagutk5h2s7ju/eVc%20v1b5.zip?dl=0 Â Pick "IR3595 test". Depending on the VID setting voltage might be a bit lower. Check which readout is correct, the 6.25mV or the 5mV version. Quote Link to comment Share on other sites More sharing options...
Smoke Posted August 3, 2015 Share Posted August 3, 2015 dont know about 980ti evga but with HOf powerboard its not working Quote Link to comment Share on other sites More sharing options...
elmor Posted August 4, 2015 Author Share Posted August 4, 2015 So the device scan is from the HOF power card? Do you get any error? Quote Link to comment Share on other sites More sharing options...
xxbassplayerxx Posted August 4, 2015 Share Posted August 4, 2015 Jon, no luck so far: Â Â Device scan 8/4/2015 2:01:09 AM: 08 0A 31 34 49 72 Quote Link to comment Share on other sites More sharing options...
Smoke Posted August 4, 2015 Share Posted August 4, 2015 So the device scan is from the HOF power card? Do you get any error? Â yes, I scan from HOF Powerboard. no error, just not changing voltage after applying Quote Link to comment Share on other sites More sharing options...
elmor Posted August 5, 2015 Author Share Posted August 5, 2015 xxbassplayerxx: Wouldn't work for the EVGA card, let me get you an updated version. Â Smoke: How about monitoring, any read out? Quote Link to comment Share on other sites More sharing options...
Smoke Posted August 5, 2015 Share Posted August 5, 2015 also not working, shows fixed 0,5v or something like this (same like xxbassplayerxx showed on pic) Quote Link to comment Share on other sites More sharing options...
elmor Posted August 8, 2015 Author Share Posted August 8, 2015 (edited) Jon, no luck so far:Â Â Device scan 8/4/2015 2:01:09 AM: 08 0A 31 34 49 72 Â Try this: https://www.dropbox.com/s/jdmf5jri6nmegnk/eVc%20v1b5.exe?dl=0 Â also not working, shows fixed 0,5v or something like this (same like xxbassplayerxx showed on pic) Â Hmm, OK. Don't have a card so can't test it myself. Can you try a register scan? Â Device address 0x06 Start 0x01 End 0xFF Â Don't check SMBus Edited August 8, 2015 by elmor Quote Link to comment Share on other sites More sharing options...
xxbassplayerxx Posted August 11, 2015 Share Posted August 11, 2015 Will give it a go. Have been benching other cards the past few days. Quote Link to comment Share on other sites More sharing options...
Guest barbonenet Posted May 11, 2016 Share Posted May 11, 2016 it works good on CHL8266, with msi 680 lightining preset. Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted September 18, 2016 Share Posted September 18, 2016 Hi, I'm trying to use this on a Gigabyte 380x G1 Gaming. It has the NCP81022, and while I've figured out how to hook up the eVc to it I'm not getting any voltage reading in the software. I've selected the generic NCP81022 and I've got current and input voltage monitoring, but there's no output voltage in the monitoring. Trying to set the voltage locks everything up and I had to reimage windows. Any ideas? Quote Link to comment Share on other sites More sharing options...
elmor Posted September 19, 2016 Author Share Posted September 19, 2016 Hi, I'm trying to use this on a Gigabyte 380x G1 Gaming. It has the NCP81022, and while I've figured out how to hook up the eVc to it I'm not getting any voltage reading in the software. I've selected the generic NCP81022 and I've got current and input voltage monitoring, but there's no output voltage in the monitoring. Trying to set the voltage locks everything up and I had to reimage windows. Any ideas?  Can you post a picture of how the interface looks like with monitoring enabled and hooked up to the card? And a register scan would help  Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted September 19, 2016 Share Posted September 19, 2016 Screenies attached. The reg scan fails with the shown error, and I have to kill the program with task manager to get out of it. Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted September 21, 2016 Share Posted September 21, 2016 Any ideas as to what might be going on? Quote Link to comment Share on other sites More sharing options...
elmor Posted September 23, 2016 Author Share Posted September 23, 2016 Any ideas as to what might be going on? Â I'm just back from vacation, will have some time to check this during the weekend. Quote Link to comment Share on other sites More sharing options...
elmor Posted September 25, 2016 Author Share Posted September 25, 2016 Any ideas as to what might be going on? Â Can you try a regscan with this version? https://www.dropbox.com/s/2qysotuywqydfqk/eVc%20v1b5%20160925.zip?dl=0 Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted September 27, 2016 Share Posted September 27, 2016 Can you try a regscan with this version? https://www.dropbox.com/s/2qysotuywqydfqk/eVc%20v1b5%20160925.zip?dl=0 Â Hi, I've attached the regscan. It crashed the first few times I tried with a .net framework error, till I started the regscan from 1 instead of 0 and also didn't select a device or enable monitoring. I've attached one of the scans from a crash as it's almost the same but has one different value show up a couple times. Thanks. Quote Link to comment Share on other sites More sharing options...
elmor Posted September 27, 2016 Author Share Posted September 27, 2016 Hi, I've attached the regscan. It crashed the first few times I tried with a .net framework error, till I started the regscan from 1 instead of 0 and also didn't select a device or enable monitoring. I've attached one of the scans from a crash as it's almost the same but has one different value show up a couple times. Thanks. Â The 060218 scan seems like it completed. Can you send me a screenshot of the .net framework error? Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted September 27, 2016 Share Posted September 27, 2016 (edited) The 060218 scan seems like it completed. Can you send me a screenshot of the .net framework error? Â Yes, that's the one that completed. I just attached the other cause it had a different value showing up in it. error when device selected and monitoring enabled is attached. Edited September 27, 2016 by Chilli-Man Quote Link to comment Share on other sites More sharing options...
elmor Posted September 28, 2016 Author Share Posted September 28, 2016 Yes, that's the one that completed. I just attached the other cause it had a different value showing up in it. error when device selected and monitoring enabled is attached. Â Try this. At least the readout and scan while monitoring should be fixed. I'm not sure why applying the voltage is failing (this was working before), but I've disabled a couple of settings to help iron out the issue. Â https://www.dropbox.com/s/vbunuoi2fsrnwwd/eVc%20160928.zip?dl=0 Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted October 5, 2016 Share Posted October 5, 2016 Try this. At least the readout and scan while monitoring should be fixed. I'm not sure why applying the voltage is failing (this was working before), but I've disabled a couple of settings to help iron out the issue. https://www.dropbox.com/s/vbunuoi2fsrnwwd/eVc%20160928.zip?dl=0  Sorry this took a while. Had my mobo die.  I've attached another register scan. It was much faster this time and ran fine with monitoring enabled. Applying a voltage still crashes the system and the GPU won't display anything till the drivers are removed. Quote Link to comment Share on other sites More sharing options...
Chilli-Man Posted October 24, 2016 Share Posted October 24, 2016 Any ideas on how I can get voltage control happening? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.