Jump to content
HWBOT Community Forums

Sin's Ultimate GIGABYTE Z97X Overclocking Guide


sin0822

Recommended Posts

Is there in both BIOS mode...

 

For persons like me (aka "the retailers")

 

There is nothing in classic mode

 

attachment.php?attachmentid=2214&stc=1&d=1403795689

 

There is nothing in uefi mode

 

attachment.php?attachmentid=2215&stc=1&d=1403795689

 

 

There might be something in ghostbuster mode , but i still havent found the combination keys to enable it. :D

Link to comment
Share on other sites

  • 4 weeks later...
  • 4 weeks later...

Hi I tested the z97x-soc force with bios f4, f6, f7d and got about 950 pts in XTU (4770k stock + 2x2gb 2000 CAS8). Then I flash with x04 during a dry ice session (could not run XTU in the session), before ending I replaced main bios with f7d. A few days later I try XTU again but I can not get 950ish, I get between 520 and 530 pts (try other bios, backup bios, fresh install, etc, and still the same). But in cinebench I get results in line with stock settings. Could it be related to the bios?

Link to comment
Share on other sites

  • 3 weeks later...

Check your uncore speed.

 

I tried a beta bios in my z97x UD3H and it set my uncore to 8 (800mhz) in Auto. I got a very low XTU score until I realised what the problem was.

 

I also found that I had to do a "clr cmos" with the power off and disconnected after a did a bios reflash to an earlier version to ensure that the new bios was loaded correctly.

 

Cheers

Edited by Rebel
Link to comment
Share on other sites

  • 3 months later...
  • Crew

Is there a way to set RTLs? Mine seem to be very high like 47/48 9/10. Also every reboot they seem to differ, so a good sp32m run is coincidence.

And how to get tcwl=6 ? Every time I try to set, board hangs with C0.

Im on Z97X SOC Force F7e and Samsung ICs running 1400Mhz CL9-12-12-21

Edited by Strunkenbold
Link to comment
Share on other sites

  • 2 weeks later...
Is there a way to set RTLs? Mine seem to be very high like 47/48 9/10. Also every reboot they seem to differ, so a good sp32m run is coincidence.

And how to get tcwl=6 ? Every time I try to set, board hangs with C0.

Im on Z97X SOC Force F7e and Samsung ICs running 1400Mhz CL9-12-12-21

 

I've had a lot of issues with board hanging at c0 when trying to get (samsung, 2800) settings that ran easily before running. I'm on X04.

Link to comment
Share on other sites

  • Crew

You definitely need X04, I train my mems now with samsung tight memory profile, then I lock rtls before I alter some of my subs. If this is booting I try to tighten rtls even more. And then I work on the subs and thirds. Often I need 1-3 trys before board boots successfully. At least I figured it out, though it seems my performance is still poor but at least Im finally under 6 minutes.

Link to comment
Share on other sites

  • 3 weeks later...
  • 2 weeks later...

guys, someone can help me out with a bios for the SOC-Force LN2 board, that can give 2.10v+ for vdimm and the gigabyte launcher oc tool is supported? with X02 bios, it does not work, and F bioses are vdimm limited by 2.10v.

 

ive seen couple guys running SOC-Force X04 on LN2 board, but if i try to flash it with qflash or efiflash ive got bios id mismatch error. any clue about to solve it? thanks

Edited by Achill3uS
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...