Is there in both BIOS mode...

they don't work in X04 there is no settings in the profiles and I don't think they work on any bios right now

Is there in both BIOS mode...

 

For persons like me (aka "the retailers")

 

There is nothing in classic mode

 

 

There is nothing in uefi mode

 

 

 

There might be something in ghostbuster mode , but i still havent found the combination keys to enable it.

Z97X-SOC Force BIOS F7a:

 

 

Z97X-SOC Force BIOS F7a:

 

That's the latest beta , right ?

 

I've got to be very brave , to flash a beta bios posted Friday 13th !!!

 

Thanks

Is there any chance , that the pre-set memory profiles are activated with certain cpu's ???

Is there any chance , that the pre-set memory profiles are activated with certain cpu's ???

 

Ive only ever had "K" CPU's in my boards.

 

Are you using an ancient BIOS?

The profiles are in all bioses

You guys do it wrong Better is set all manually and make your own Profile!

Who cares profiles lol^^

I think they want the timings, in that case maybe load a profile, see the timings it sets and then make your own profile using the timings as a starting point

How do you get bclk to work in GTL on XP? I have tried the linked MEI and installed it via device manager but no luck with bclk adjustment. Thinking it's my OS at this point . . .

I was using mei from maximus VII oc pack and turbov was then able to change bclk on the fly.

Hi I tested the z97x-soc force with bios f4, f6, f7d and got about 950 pts in XTU (4770k stock + 2x2gb 2000 CAS8). Then I flash with x04 during a dry ice session (could not run XTU in the session), before ending I replaced main bios with f7d. A few days later I try XTU again but I can not get 950ish, I get between 520 and 530 pts (try other bios, backup bios, fresh install, etc, and still the same). But in cinebench I get results in line with stock settings. Could it be related to the bios?

Check your uncore speed.

 

I tried a beta bios in my z97x UD3H and it set my uncore to 8 (800mhz) in Auto. I got a very low XTU score until I realised what the problem was.

 

I also found that I had to do a "clr cmos" with the power off and disconnected after a did a bios reflash to an earlier version to ensure that the new bios was loaded correctly.

 

Cheers

Edited September 9, 201410 yr by Rebel

I manually enter uncore, also test the bios x04, and no changes, xtu 530 and cinebench, wprime, hwbotprime correct results.

switch to 7sp1. Without service pack results are bad

Yes, this is my bench O.S.

Is there a way to set RTLs? Mine seem to be very high like 47/48 9/10. Also every reboot they seem to differ, so a good sp32m run is coincidence.

And how to get tcwl=6 ? Every time I try to set, board hangs with C0.

Im on Z97X SOC Force F7e and Samsung ICs running 1400Mhz CL9-12-12-21

Edited January 8, 201510 yr by Strunkenbold

where can i get the X04 bios??

Here's all you need for gigabyte.

 

http://forums.tweaktown.com/gigabyte/28441-gigabyte-latest-beta-bios.html

Is there a way to set RTLs? Mine seem to be very high like 47/48 9/10. Also every reboot they seem to differ, so a good sp32m run is coincidence.

And how to get tcwl=6 ? Every time I try to set, board hangs with C0.

Im on Z97X SOC Force F7e and Samsung ICs running 1400Mhz CL9-12-12-21

 

I've had a lot of issues with board hanging at c0 when trying to get (samsung, 2800) settings that ran easily before running. I'm on X04.

You definitely need X04, I train my mems now with samsung tight memory profile, then I lock rtls before I alter some of my subs. If this is booting I try to tighten rtls even more. And then I work on the subs and thirds. Often I need 1-3 trys before board boots successfully. At least I figured it out, though it seems my performance is still poor but at least Im finally under 6 minutes.

Any chance of getting the XP MEI link working again? Have just moved up from the Z87X-OC and trying to get drives etc set up.

 

Cheers

Any chance of getting the XP MEI link working again? Have just moved up from the Z87X-OC and trying to get drives etc set up.

 

Cheers

 

Here is the driver i found on my PC for Z97 XP MEI

 

https://www.mediafire.com/?23gy9z3dugifw1c

Here is the driver i found on my PC for Z97 XP MEI

 

https://www.mediafire.com/?23gy9z3dugifw1c

 

Awesome thanks Dino.

guys, someone can help me out with a bios for the SOC-Force LN2 board, that can give 2.10v+ for vdimm and the gigabyte launcher oc tool is supported? with X02 bios, it does not work, and F bioses are vdimm limited by 2.10v.

 

ive seen couple guys running SOC-Force X04 on LN2 board, but if i try to flash it with qflash or efiflash ive got bios id mismatch error. any clue about to solve it? thanks

Edited February 23, 201510 yr by Achill3uS