buildzoid Posted August 13, 2016 Share Posted August 13, 2016 Ok so I just did my very first LN2 session with the RX 480. So I figured I'd share my expirience for anyone else intrested as well as start a generally discussion about pushing the RX 480 on cold. Stuff to be aware of My reference card didn't have either CB or CBB so I ended up running full pot. However I do suspect that my mounting might have failed at some point in time because I was clocking a little low and because I couldn't use the backplate for my Raptor 4 due to it conflicting with my extra cap placements. If you can get into BIOS but not into windows then you need to go into safe mode and reinstall the drivers because Wattman remembers your last unstable OC and is trying to boot with it(praise AMD! /s). If you have an SSD and a clean setup this should not take too long. - Stuff to use to overclock. As of right now Elmor's LN2 BIOS + GPU Tweak II is the best for voltage control and clocks since it goes to 4Ghz core and 18Ghz mem as well as 2V on the core(not that you will ever reach any of those). At 150% power limit the BIOS gives you a 450W power limit. - Display going black when running benches. The card has black screen issues. If you push it really low(like say the -178C that I ran at according to my dodgy equipment) with high core voltage you will lose the display. The benchmark is still running you just can't see it. In theory this should be solvable by putting more volts on the .95V rail but I can't figure out how to Vmod it yet. Once I do I will test. To see if the card is running you when blackscreened you need to use a DMM on either Vcore or Vmem as either will show the impact of 3D load. For me mem would hit 1.571V under load and idled at 1.551V. Overclocking - Core overclocking I could run windowed 3DM firestrike 1280x1050(IIRC not sure about the resolution) at 1600mhz however my best pass of Firestrike proper was only 1550mhz. Neither more Vcore(tested 1.4-1.6V) nor cold did anything. I suspect I may have just had a bad mount or something which caused these problems. Once I bench again I will know for sure. It is also possible my card just doesn't scale at all. - Memory overclocking The Samsung memory on my 8GB reference card seems to absolutely hate cold and voltage. I modded my card for 1.72V mem. That didn't help OCing at all. I also tried more VCCI(the voltage in the memory section of Wattman) that also didn't help either and led to the second driver reinstall I did in my session with the card. The card could pass benches at 9Ghz mem on ambient. With the PCB freezeing through I was fighting for 8.5Ghz so I guess the RAM didn't like the cold either. The 4GB Hynix cards are probably a better choice for pure clock speed on cold IDK about performance someone would need to do a test. BTW here's the memory voltage mod for reference PCB cards(it should be compatible with all card using the GS7256 controller): http://i.imgur.com/fZz3lPz.png 1 Quote Link to comment Share on other sites More sharing options...
flanker Posted August 21, 2016 Share Posted August 21, 2016 Man, going to czech forum also. You will be welcome in pctuning forum. I believe, your czehc will be better than my english Quote Link to comment Share on other sites More sharing options...
buildzoid Posted August 22, 2016 Author Share Posted August 22, 2016 Man, going to czech forum also. You will be welcome in pctuning forum. I believe, your czehc will be better than my english My spoken Czech might be. But my written Czech is terrible. Quote Link to comment Share on other sites More sharing options...
flanker Posted August 22, 2016 Share Posted August 22, 2016 My spoken Czech might be. But my written Czech is terrible. Im sure better than my english Quote Link to comment Share on other sites More sharing options...
buildzoid Posted August 25, 2016 Author Share Posted August 25, 2016 Ok so I just noticed something weird. If I try to set over 9Ghz mem in GPU Tweak II with extended OC range it just goes back to 9Ghz. Is there any chance of a fix for this? I was hoping that with more Vmem I could push as much as 10GHz but if the software doesn't allow above 9Ghz I can't really do anything. Quote Link to comment Share on other sites More sharing options...
elmor Posted August 26, 2016 Share Posted August 26, 2016 Ok so I just noticed something weird. If I try to set over 9Ghz mem in GPU Tweak II with extended OC range it just goes back to 9Ghz. Is there any chance of a fix for this? I was hoping that with more Vmem I could push as much as 10GHz but if the software doesn't allow above 9Ghz I can't really do anything. It's limited by AMD in the driver. Quote Link to comment Share on other sites More sharing options...
flanker Posted August 26, 2016 Share Posted August 26, 2016 Maybe The Stilt could help with it. Quote Link to comment Share on other sites More sharing options...
buildzoid Posted August 26, 2016 Author Share Posted August 26, 2016 It's limited by AMD in the driver. Yeah I figured as much Quote Link to comment Share on other sites More sharing options...
kenneth.mes Posted September 13, 2016 Share Posted September 13, 2016 I've had issues with certain overclocking programs creating visual artifacts once loaded, even if everything is left at stock, I think it's a conflict with AMD's own drivers sometimes. Have you tried overclocking through CCC? Also, what driver are you using? Quote Link to comment Share on other sites More sharing options...
benchmark.kz Posted November 11, 2016 Share Posted November 11, 2016 Hello guys! Is it possible to make GPU Clock as constant? Trying to do 1400/2000 MHz on my ASUS DUAL-RX480-O4G on stock, but it always downclocking to 1368 MHz by core. PS: I didn't overclock anything about two years.... >_< Quote Link to comment Share on other sites More sharing options...
Splave Posted November 11, 2016 Share Posted November 11, 2016 I have cold slow at 0c Powercolor card Quote Link to comment Share on other sites More sharing options...
buildzoid Posted November 12, 2016 Author Share Posted November 12, 2016 I have cold slow at 0c Powercolor card Try the Elmor LN2 BIOS. It should work on most cards that are close to reference(XFX GTR, Powercolor Red Devil) or reference PCB. I haven't yet started on trying to figure out how the Elmor LN2 BIOS works. Currently busy messing with RAM timings and then getting a full Vmod(Vmem, AUX and 0.95V) guide done for the RX 480 GTR PCB. Quote Link to comment Share on other sites More sharing options...
Splave Posted November 12, 2016 Share Posted November 12, 2016 black screen on boot with elmor bios on red devil Quote Link to comment Share on other sites More sharing options...
buildzoid Posted November 12, 2016 Author Share Posted November 12, 2016 black screen on boot with elmor bios on red devil Good to know I'll see if I can work something out. Does the air BIOS work by any chance? I haven't tried the LN2 BIOS on my GTR yet. BTW the Red Devil has one of the weakest VRMs of the RX 480s so if you bench it on air/water keep the VRM temperature low or it might burn out when doing 1.3V+ approaching or exceeding 1500mhz. Quote Link to comment Share on other sites More sharing options...
Splave Posted November 12, 2016 Share Posted November 12, 2016 Air bios no go as well. The original unlocked red devil bios can do quite well I was surprised but 0c it down clocks Quote Link to comment Share on other sites More sharing options...
buildzoid Posted November 13, 2016 Author Share Posted November 13, 2016 So I just did some testing and I found something rather odd. The memory voltage setting in Wattman doesn't seem to do anything. I've tested values from 800mv to 1150mv and when checking the various VRMs on my card with a DMM I found that none of the voltages actually changed. So I'm wondering if that voltage setting even does anything. Because after some closer investigation of the PCB I found that the 1V AUX rail is using one of those APW8722 controllers which don't support software voltage control. The IR 3567B seems to only control the core voltage and nothing else. Quote Link to comment Share on other sites More sharing options...
matty50racer Posted April 28, 2019 Share Posted April 28, 2019 On 11/13/2016 at 7:08 AM, buildzoid said: So I just did some testing and I found something rather odd. The memory voltage setting in Wattman doesn't seem to do anything. I've tested values from 800mv to 1150mv and when checking the various VRMs on my card with a DMM I found that none of the voltages actually changed. So I'm wondering if that voltage setting even does anything. Because after some closer investigation of the PCB I found that the 1V AUX rail is using one of those APW8722 controllers which don't support software voltage control. The IR 3567B seems to only control the core voltage and nothing else. I know this is old but in my testing I have found that it is just the miniumum voltage that the core needs at maximum memory frequency. I needed to raise this slightly to stop crashing at low loads like chrome browser when pushing the memory hard. Quote Link to comment Share on other sites More sharing options...
Nik Posted January 2, 2020 Share Posted January 2, 2020 (edited) Hi, Run elmor ln2 bios with Rx580 strix? Search a tool and bios for open voltage ? Thanks Edited January 2, 2020 by Nik Quote Link to comment Share on other sites More sharing options...
ShaggySVK Posted January 6, 2020 Share Posted January 6, 2020 For me Elmor BIOS also caused blackscreen. Already had LN2 pot on the GPU at time of flashing Didnt backup the original BIOS, so will have to download from second GPU. Do you maybe know which string is related to OTP? Maybe what needs to be done? Reference RX480, not aftermarket. Quote Link to comment Share on other sites More sharing options...
elmor Posted February 23, 2020 Share Posted February 23, 2020 Someone could try this: https://1drv.ms/u/s!Atmpv-6qHr_6g94Oj4zXRtYE51Ti5g?e=eDagy0 Might need to re-install the driver if it doesn't work 1 Quote Link to comment Share on other sites More sharing options...
KaRtA Posted February 27, 2020 Share Posted February 27, 2020 Hey @elmor, do you have LN2 bios for Reference RX580? I flashed with RX480 but black screen reboot hell. Quote Link to comment Share on other sites More sharing options...
elmor Posted March 3, 2020 Share Posted March 3, 2020 On 2/27/2020 at 6:02 AM, KaRtA said: Hey @elmor, do you have LN2 bios for Reference RX580? I flashed with RX480 but black screen reboot hell. Sorry, I don't. Do you get cold slow problems? Quote Link to comment Share on other sites More sharing options...
KaRtA Posted March 3, 2020 Share Posted March 3, 2020 Yes, it appears like I do. Hooked on the single stage and would be lucky to boost to 900mhz at stock. If I reduced voltage, it would get to 1300 boost, but who wants that. it’s ok though, I have a beta bios to try for it now. Not the greatest sample around but enough to have fun with. Quote Link to comment Share on other sites More sharing options...
unityofsaints Posted January 28, 2021 Share Posted January 28, 2021 On 3/4/2020 at 8:28 AM, KaRtA said: Yes, it appears like I do. Hooked on the single stage and would be lucky to boost to 900mhz at stock. If I reduced voltage, it would get to 1300 boost, but who wants that. it’s ok though, I have a beta bios to try for it now. Not the greatest sample around but enough to have fun with. What RX480 do you have? For the STRIX there's a tool that lets you set the voltage slope, effectively doubling the power limit. On other SKUs you might have to epower. Quote Link to comment Share on other sites More sharing options...
KaRtA Posted February 3, 2021 Share Posted February 3, 2021 it was cold slow mate. I have a special bios to retry Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.