March 11, 20178 yr No problem with my board. Only ever had usb problems on msi z170 xpower, but it was usb ocp and fixable.
March 11, 20178 yr Ok, if you can't/don't want to rma then you can measure the resistance of the fuses near the usb ports. Any fuse with infinite resistance needs to be shorted.
March 11, 20178 yr Ok, if you can't/don't want to rma then you can measure the resistance of the fuses near the usb ports. Any fuse with infinite resistance needs to be shorted. Thanks for that Tobias Can bios flashing be done via usb on pcie card??
March 12, 20178 yr Author We have some issues with some of the on-board fuses getting stuck in protection mode. It seems to happen easier if the board gets very cold. Simplest fix is to short them. Location of fuses: Edited December 14, 20177 yr by elmor
March 15, 20178 yr Author USB overcurrent disabled in this bios, based off 0801. MAXIMUS-IX-APEX-ASUS-0023-USBOC
March 15, 20178 yr USB overcurrent disabled in this bios, based off 0801. MAXIMUS-IX-APEX-ASUS-0023-USBOC Awesome, thanks Elmor
March 20, 20178 yr Does anyone same experience as me on 0801 BIOS? It bootloop about 5 times before post, post code before reboot loop 9A. But its working fine. Is it normal as i not seeing it on 0701 BIOS? Thanks in advance, best motherboard, period
March 20, 20178 yr Does anyone same experience as me on 0801 BIOS? It bootloop about 5 times before post, post code before reboot loop 9A. But its working fine. Is it normal as i not seeing it on 0701 BIOS? Thanks in advance, best motherboard, period No not that one, usually see 14 a few times before booting
March 20, 20178 yr @elmor - is it possible to flash OC Panel 1 firmware on these boards from Haswell firmware, or do I need to find a Haswell setup to flash it to suit Maximus IX? Hope that made sense.
March 21, 20178 yr Author @elmor - is it possible to flash OC Panel 1 firmware on these boards from Haswell firmware, or do I need to find a Haswell setup to flash it to suit Maximus IX? Hope that made sense. Yes, you can update the OC Panel on newer platforms.
March 22, 20178 yr Does anyone same experience as me on 0801 BIOS? It bootloop about 5 times before post, post code before reboot loop 9A. But its working fine. Is it normal as i not seeing it on 0701 BIOS? Thanks in advance, best motherboard, period I haved the same problem with 3 motherboard and with bios 0026/0701/0801. With 0088 and 0091 i not have 4/5 fake boot.
March 23, 20178 yr I reflashed again from USB Bios Flashback (again) and problem is gone. I will see in few day if its still has same problem.
March 24, 20178 yr Bootloop happen again, its very annoying for B-Die when did tight timing bootloop for 5 times with slow boot (i tested for daily use too still did bootloop about 3-5 times), but it doesnt happen on 0701, so its fixable i think
March 25, 20178 yr MAXIMUS IX APEX BIOS 0906 1.Complete support for Intel® Optane Memory 2.Fixed PXE issue. 3.Fixed M.2 device issue (Plextor) 4.Fixed MemTest86 issue in multi-CPU selection modes http://dlcdnet.asus.com/pub/ASUS/mb/LGA1151/MAXIMUS_IX_APEX/MAXIMUS-IX-APEX-ASUS-0906.zip?_ga=1.218967514.252291305.1488625082
March 27, 20178 yr MAXIMUS IX APEX BIOS 09061.Complete support for Intel® Optane Memory 2.Fixed PXE issue. 3.Fixed M.2 device issue (Plextor) 4.Fixed MemTest86 issue in multi-CPU selection modes http://dlcdnet.asus.com/pub/ASUS/mb/LGA1151/MAXIMUS_IX_APEX/MAXIMUS-IX-APEX-ASUS-0906.zip?_ga=1.218967514.252291305.1488625082 This BIOS is very good at mem! My B-Die that only scale up to 1.9v until 0801, in this bios can run at 1.94v. So from 4000 12-11-11 1.9v can run at 4060 12-11-11 1.915v (and still run stable at 1.94v)
March 27, 20178 yr Hi P5ych0, on air. With my b die that dont scale with v. Alex@ro, all of them can run xp easy. I testing it on 32m with waza.
March 27, 20178 yr Are you willing to share your prepared XP for Apex. [emoji2] Cheers... Edited March 27, 20178 yr by P5ych0
March 27, 20178 yr Ok so I finally got a B-die kit and a 7700K and in my first 6 hours with kit on the board I got 4000 12-13-13-28-1T working on 1.97V 32M stable. However the moment I set 4000 12-12-12-28-1T on any voltage from 1.88V to 2.05V I get a 3F POST code. Am I correct in assuming that my 7700K's IMC is the problem?
March 27, 20178 yr I have 2 7700k ,nothing special , and both can do over 4150 12-11-11 tight with vccio 1.2 & vccsa 1.25. I don't think you have imc issues,just settings not alright or mem not capable. Try with dram vtt between 0.83-0.87v . On what windows are you testing,x64 ? Sent from my iPhone using Tapatalk Pro
March 28, 20178 yr Ok so I finally got a B-die kit and a 7700K and in my first 6 hours with kit on the board I got 4000 12-13-13-28-1T working on 1.97V 32M stable. However the moment I set 4000 12-12-12-28-1T on any voltage from 1.88V to 2.05V I get a 3F POST code. Am I correct in assuming that my 7700K's IMC is the problem? Switch maximus tweak to 1 or Auto, works better at 4k c 12... With BIOS 0701 0801 Cheers...
March 28, 20178 yr Do any of you have issues with Apex and low scores on xp/xp64 with gen 2 graphic cards in 3Dmark 2001/2003 ? Compared with z170 and similar settings gt1 is lower and 2001 overall gives lower score. Any magical settings for legacy ? Sent from my iPhone using Tapatalk Pro
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.