Bullant

Hey mate, sorry I never received this board.....only used it for a short time from a friend before I retured it. Dino or Sofo should be able to help you

Great, hope it all goes well mate....I'll try rerun myself in couple weeks

Sorry double post

Hey mate, yeah for me I have cb if I push memory freq "imc" to high, or have to high nb-CPU volts, you know the volts we use for nb freq. So yeah if you have cb that can start at around -160 to -170 try lowering memory freq a little or try set lower nb-CPU volt the one we use for nb freq, normally once you get it full pot you can then push memory, nb freq and nb-CPU volts with this chip chip and psc I had problems to start with also, so I was 2160 mem with cb -165 had to drop mem to 2000 and cb went to -180....once I was full pot I could then push all my chips do it, just some are worse then others and normally lower nb-CPU volt alows me to go full pot, then can smash volts.....,also start with lower nb freq just to get full pot Hey mate, yeah it'll do 2200 6-8-6-21......but with 5 lrts and trying to work CPU max out, thought not good idea to push memory lol Great to see you around mate

Nice loud

Looks good mate, the ud5 rev2? It should go ok on psc-bbse

Thanks mate, I need to find a better one of these chips....is a few on ebay but not local, ill keep looking

So you can't reproduce like you old results? Same OS and all?

Yeah the faster second run I think was my waza, every run I tried after that failed run was faster then the failed run. Even tho start time is the same, my waza does vary Yeah I have a ud5 too that not like my hypers but it likes the psc, I thought it might have been bios, I've yet to try another bios. Have you tested the ud5 on eff or is the memory that works on it not great?

So it was cache freq holding it back, I adjusted some volts and lowered v core a little to get the pass

Went to test this chip for freq, not great...so ran some more 5G....UD7...Hypers 1.87v The bottom fail 13m.11 xxx, I say and maybe 3 sec faster on the UD5, will run that up another time

Ran the 965 BE on the ud7....was only quick session, should drop few more sec with more memory and cache

Nice work man, these chips look like fun

Yeah some of them are strange CPUs ahaha, just for reference my ud7 is rev 2 thanks guys

Not sure man, this score was about 200 points down on my ud5 test yesterday....but I ran the ud5 on PSC and the ud7 on hypers.So was either board on memory was the difference Maybe it could be you bios settings or memory?

Thanks guys

Hey, yeah the problem I have is for me dram volts not scale higher then say 1.87v, both psc and hypers. I've only tested one kit of hypers and two kits of PSC... Yeah was only quick testing but yeah if I loosen tras to say 24 it would help a little, with maybe loosing some eff. That 2200 run was with -45 1.87v, it even ran a little at -100.... 2200mhz 6-8-6-21-18, very fast but dram volts limit 1.87v will play around little more more with some volt settings to see if any help ?

Ran a couple 4Ghz runs, memory -100

Just a quick one tonight, memory -5....Will push some more over the weekend

Oh I just bought this board to go with a 9900K , is the std 1704 bios ok for everything including LN2 and memory clocking? Im assuming just no xp?

Will have ln2 on Friday, so I'll run up the CPU and memory "PSC" both ln2 Should see nice boost in eff both from cache and higher and tighter memory freq Will gradually drop memory temperature while working out dram scaling will post results and findings

Ran again on a different Gigabyte board, would need to look over bios more to compare with other board, just in case Ive done them different. It all takes time lol

From what I've seen and tested....,the difference between rev2 vs rev3 is "rev2" uses 3-4 slots close together and "rev3 has the more modern 2-4 of set slot usage That being said 890fx that runs memory 2-4 slots and 990fx can run 4x dims at good memory freq....no boost in 32m but good boost in some benches I've eff tested I do have both ud5 890fx revs that use the 3-4 and 2-4 slot setups, Ill have to test both to see if memory and eff difference My 890fx ud7 rev2 using 3-4 slots was doing a little better stable memory clock then the ud5 I've posted yesterday, that being said the ud5 I've not tried and tested other bios yet

You should mate, I'll try post some ln2 runs hopefully this weekend

5G Thuban , will run it up again later