Jump to content
HWBOT Community Forums

Zen SuperPI 32M 5G/4G Challenge


Massman

Recommended Posts

On 12/13/2020 at 11:38 AM, Dancop said:

Next step is 4k mem with 2k fclock... But there seems to be no way to run it like that actually

2434590.jpg

Jack up your PLL voltage to about 2.1v. Benching only........do not take this advice anyone running 24/7.........

 

4000_pll2.15.jpg?width=1606&height=904

Edited by chew*
Link to comment
Share on other sites

4 minutes ago, chew* said:

Jack up your PLL voltage to about 2.1v. Benching only........do not take this advice anyone running 24/7.........

High pll buys you about 200 mhz more mem clocks linked. without it the chVIII non dark is capped at 3800/1900. If you experience slowdown crank it till you don't....... Board choice seems to matter alot as to how high the fclk can go linked to mem, as long as the vendors aren't already playing games with pll you should be able to gain 200 mem/100 fabric.

 

 

Quote

 

4000_pll2.15.jpg?width=1606&height=904

 

Edited by chew*
  • Like 1
Link to comment
Share on other sites

18 hours ago, OClockDoc said:

Still can't understand why board goes in slow mode with certain mem multiplayers:

 

rSg7Bqz.jpg

 

Otherwise very happy with the board. Pi 32M 2x8GB DDR4@3800MHz 11-11-9-9-21-29-1T 

 

Dxk3D2Q.jpg

 

My guess would be aggressive error correction. 2000 is not really any more stable than 3933 or 3966 all produce whea errors when not cutting OS memory down via maxmem. 3800 and lower is perfectly fine if there is no post hole which apparently even on DARK my 5900 has at 3800 with 07 post code. 3800+ boots fine but wheas.

  • Like 2
Link to comment
Share on other sites

On 12/21/2020 at 9:19 PM, chew* said:

My guess would be aggressive error correction. 2000 is not really any more stable than 3933 or 3966 all produce whea errors when not cutting OS memory down via maxmem. 3800 and lower is perfectly fine if there is no post hole which apparently even on DARK my 5900 has at 3800 with 07 post code. 3800+ boots fine but wheas.

Shure, I know the mem is unstable, but same settings works fine for 4000 and even 4066. That is why supposed it is BIOS issue.

On 12/21/2020 at 10:23 PM, Sparky's__Adventure said:

@OClockDoccan you do tCWL 9, tWRRD 1, lower tWTR L/S?

Also does higher ProcODT have any affect on time?

tCWL 9 is no go,  tWRRD 1 is fine, but don`t think it`s faster,   tWTR L/S=3/8 lowest possible for me. I don`t think  ProcODT has direct affect on time, may be stability issue affecting time.

2x8GB DDR4@3800MHz 11-11-8-9-21-29-1T 

O18iryS.jpg

Edited by OClockDoc
  • Like 1
Link to comment
Share on other sites

10 hours ago, OClockDoc said:

Shure, I know the mem is unstable, but same settings works fine for 4000 and even 4066. That is why supposed it is BIOS issue.

 

O18iryS.jpg

3/8 used to work better for me on R1 as well. Not sure if your sticks can do it but 10-9-9 showed a lot of promise in the past, don't bother with cas 9 though it was slower than c10. dropping twcl -2 of CL is an intel thing. AMD likes them =.

Honestly I ran some aggressive settings the other night vs my daily mem timings. I'm not seeing anything spectacular.

100 mhz is worth 15 secs on avg. im doing 6:00 at 4850mhz on prime stable settings and 6:15 and 4750mhz. Honestly the times im seeing are where they are supposed to be for the cpu speed and the memory tuning gains are like pulling teeth for any gains.

I see what you meant about certain dividers. fwiw at least yours can boot. 5900x boots 3733, 07 hang @ 3800, boot 3866 all the way to 4066 so lol..... That's on the dark but my 5800x is fine......

 

Link to comment
Share on other sites

2 hours ago, chew* said:

lol yah that was a zen 1 thing for launch agesa.

Yeah I’ve not ran no ddr4 AMD so didn’t know if it was still the same as early release....good to know it’s all unlocked now 

 

thanks mate 

 

 

Edited by Bullant
Link to comment
Share on other sites

  • 4 weeks later...
  • 2 weeks later...
On 12/22/2020 at 10:52 PM, OClockDoc said:

Shure, I know the mem is unstable, but same settings works fine for 4000 and even 4066. That is why supposed it is BIOS issue.

tCWL 9 is no go,  tWRRD 1 is fine, but don`t think it`s faster,   tWTR L/S=3/8 lowest possible for me. I don`t think  ProcODT has direct affect on time, may be stability issue affecting time.С2x8GB DDR4@3800MHz 11-11-8-9-21-29-1T 

O18iryS.jpg

Some improvement with tFAW=6. Strange, because it shouldn't  be possible.

2021-01-28_223527.png

  • Like 3
  • Thanks 1
Link to comment
Share on other sites

  • 3 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...