June 23, 20168 yr Not easy to tune B-die above 3866 on the OCF. Out of five kits, my best one does 3980 ( shy of 4000 ), at 12-11-11-28-200-1T. with extremely tight seconds and thirds. RTL and IOL set respectively at 49-50 / 6-6. This needs 1.90V and 1.16VccIO and 1.35VccSA. Most of all it needs strong cooling of the memory sticks and an IMC with balls. I have not found these settings useful in many benchmarks. Exhaustive testing has proven that so tight settings could turn around and become a bottleneck. The golden rule of balancing the whole system applies. Maximum speed and tight timings is not always the way to go. I did not, yet, have the opportunity to test M-OCF, because I received a dead board. Waiting for a new one from Germany.
June 24, 20168 yr how to save a profile to a USB flash? I've tried, but my flash is not readable my flash formatted ntfs
June 28, 20168 yr Some retail memory,no waza on air,all tight and do pass 4 loops waza....Little cold on mem they should pass with waza [/url
July 1, 20168 yr Some Kingston AFR,cpu water and memory air,testing OS setup with page file and waza size, faster start slower end half with better final loop to end with much same as my last time Edited July 1, 20168 yr by Bullant
July 1, 20168 yr Team group mems water-air Kingston AFR,little cold on the memory's,will go colder on the memory's and test tighter cl next time
July 2, 20168 yr Another quick test on AFR tonight,will see how much I can tighten up on next session
July 3, 20168 yr Is this with ln2 cooling? Yes mate,memory are on ln2 on that run Edited July 3, 20168 yr by Bullant
September 5, 20168 yr Quick run on retail mfr and four dim board,have ordered a new two did board will re run on that in few days,should see little more
September 20, 20168 yr Was doing some afr testing last night,memory only little cold -15 wow crazy frequency for that temp, really amazing.
September 21, 20168 yr wow crazy frequency for that temp, really amazing. Yeah man AFR are really nice scaling on cold,when I have more ln2 I'll try them colder and see how much freq I can get from them at say these timings,32m vs xtu is little different cause if I try xtu I can run full pot memory -170 and could see some crazy scaling but with 32m can't run full pot mem -80 to -120 depending on mem Just in xtu I did test at say only -100 and was running 12-18-18 4220mhz pass so on full cold mems should see it tighter timings a least if not more MHz,b die is also good cold scaling on xtu up to temp limit (more MHz eff scaling on xtu not sure but MHz and tight timings scaling yes) Edited September 21, 20168 yr by Bullant
September 22, 20168 yr Yeah man AFR are really nice scaling on cold,when I have more ln2 I'll try them colder and see how much freq I can get from them at say these timings,32m vs xtu is little different cause if I try xtu I can run full pot memory -170 and could see some crazy scaling but with 32m can't run full pot mem -80 to -120 depending on mem Just in xtu I did test at say only -100 and was running 12-18-18 4220mhz pass so on full cold mems should see it tighter timings a least if not more MHz,b die is also good cold scaling on xtu up to temp limit (more MHz eff scaling on xtu not sure but MHz and tight timings scaling yes) Hey bully shot you a pm.
October 10, 20168 yr This board needs DRAM VTT setting, I know it's not in latest retail. Is it in any of the beta BIOSes?
November 20, 20168 yr Some AFR and Maxmem Memory read,Cpu single stage -30 and memory on "ice blocks" about 10c.Will run both on LN2 later,should see nice boost
December 9, 20168 yr Finally got around to testing those retail mfr on cold again,while I can push them to 3800 11-15-15 I just cant seem to get them to do 32m 3733+ stable 1.76v......... Edited December 9, 20168 yr by Bullant
December 28, 20168 yr Does anyone have any insight into today's (28 Dec) BIOS release (7.30)? I was hoping Kaby Lake would show up on the QVL.
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.