6-9-6 would be pretty awesome tho ^^

 

6-9-6 under cold has been done before at 2500

 

http://www.xtremesystems.org/forums/showthread.php?280903-SuperPi32m-5Ghz-Ivy-All-Out-Challenge!&p=5101956&viewfull=1#post5101956

I just got a UP5 and i am testing it.

1st Boot A6 Error, not even signal to monitor.

After many boots and CMOS the same.

I as using 3770K with the integrated VGA.

 

Then i used a 560 and i booted the 1st time.

Switch bios from F1 to F6X.

Everything ok with the 560.

Switch from 560 to integrated i am getting errors A6 or A0.

 

Anybody has the same problem?

I think you mean "Ab", but Ab is not an error, it is just Ab and it means you are in the BIOS but video output is up to you.

 

If you have a GPU plugged in, the board always defaults to it. So you can pull the GPU out and then try integrated, if one of those outputs don't work then you can try another.

Yeah...it is maybe Ab and i read in another forum that he thougths is was A6 too.

My problem is that a PCI-E VGA is giving me output but the integrated one is not working for me neither from VGA nor from DVI

plug.

 

I read that someone booted the PC and then plugged the VGA cable but this didn't worked for me.

I want to work with the integrated one as you understand

you can set the igp to default to the first display device in bios. alternatively, you can pull the discreet video card out completely, clear cmos, then boot with the onboard video connections.

I have done all those things...nothing is working!

Seems like the plugs are dead or something...

I had a similar issue like Gorillakos on the UP4 before, but it got fixed magically. What I did was:

 

- boot up with pcie gpu

- set igp to default in bios

- save, exit shutdown

- remove pcie gpu

- boot with igp

- clear cmos (long hold)

- boot with igp always

 

After that, I never had issues with booting from the IGP again.

yea you have to set INIT display first to IGFX, that is what i do and then remove the dGPU. I know it is kind of a pain.

Guys try new BIOS.

@Massman i have done this more than 10 times...not working for me. In the end i am getting A0 Error and never see nothing on my screen.

@sin You say it's a kind of pain cause you are removing the VGA while you are in bios?

@stasio i got the F6X..which is the newest?

 

EDIT: Ok seen it the F9...going to put it

Edited August 28, 201212 yr by GoriLLakoS

F9 Installed again the same!

 

I switched to 3770S, same again!

I cleaned the CPU and installed everything from the start for 30th time and suddenly everything worked out :D

 

Thanks for all the support guys :T:

which video output do u use?

 

Ab= you are in the BIOS

A0= you are in OS

Is that on air or with the memory under LN2, Dino?

 

Maybe we should track what PSC/BBSE is actually working with what MB/BIOS/REV? Track it down to serial number?

LN2 of course man, never seen people do that with air cooled RAM faints

 

6-9-6 under cold has been done before at 2500

 

http://www.xtremesystems.org/forums/showthread.php?280903-SuperPi32m-5Ghz-Ivy-All-Out-Challenge!&p=5101956&viewfull=1#post5101956

so did i on UD5H but that's not that impressive, 7-11-7 at 1300+ is faster

http://www.xtremesystems.org/forums/showthread.php?280903-SuperPi32m-5Ghz-Ivy-All-Out-Challenge!&p=5112064&viewfull=1#post5112064

With Massman in the Epicentre of GB knowledge, I'm eagerly awaiting a bios to try.... Heck I might even flash F14 tonite on the UD5H

Seems like it failed?

Seems with proper BIOS (nickshih),guys easily reaching DRAM 2800+ on Asrock Z77 OC Formula.

 

http://www.xtremesystems.org/forums/showthread.php?282693-**-OFFICIAL-**-Asrock-Z77-OC-Formula-Overclocking-troubleshooting-Discussion/page10

Now that's what I call bios improvement

^ yea,you are right........and yesterday Nickshih with ASRock Z77 OC Formula Sets a New World Record............7.136 GHz!

 

http://www.techpowerup.com/172189/ASRock-Z77-OC-Formula-Sets-a-New-World-Record.html

reminds of the numerous FDI biosses per ram kit... could make some clockers swap sides...

Can someone upload the SPD of the tridentx with sammy modules?Or any XMP of samsung based modules?I'm having great issues with a biostar TZ77x anything above 2133 will give me 55 code and not work regarding latency's and voltages of SA VCCIo etc.Have sammy 30nm YK0 they do 9-10-10-27-1 2133 with 1.5V but nothing more on this Biostar board,always 55 code.

 

Thanks,.

2666C11 plats on Gene V XMP profile :

 

 

Try 11-13-13-30 2T 1.65Vdimm and see if 2400 boots with above sec and tertiary timings...

If that's as Samsung as it looks, you could pull that tRFC time in by 80-100 cycles couldn't you?

Jups Kenny, TRFC 127 is smooth as butter... You can insanely lower tRAS too (18-20), tWWSR is too loose too on the ASUS, eg the MSI board sets 5 for the same XMP profile...

I mis-read the tRAS in your screeny, yea, 21 is good for me I can also pull tWR in to 10 without a problem. I've not got DEEP with timings though. First Ivy SPi session tonight though I hope this CPU is as good as I hope

On the UD5H ? fingers crossed you have at least a 6.7Ghz CPU...