October 14, 201311 yr Author Both scores have been removed from the competition because the kits (with MFR) are not retail. This has been confirmed by Kingston.
October 14, 201311 yr These are MFR based you are right but not retail yet so no reason to allow them.
October 14, 201311 yr Crew for those who are not on my facebook, kingston BDBG 2133 C9 H20 kit doing lovely on LN2. fullpot 2.2v. 32m is 1400 7-12-7 easy, now to finetune
October 14, 201311 yr Actually, you don't even need to look at the cap arrangement to verify if these are SS or not. Vertical code - symbols 4 to 6 indicate number and manufacturer of ICs used. http://img.hwbot.org/u31047/image_id_1038878.jpeg H = Hynix, 08 = eight ICs, single-sided http://content.hwigroup.net/images/products/xl/161001.jpg S = Samsung, 16 = sixteen ICs, dual-sided
October 14, 201311 yr Was going to ask if Kingston's PDFs were accurate on wether they were single side or not in general....seems not PDF shows single sided when clearly they are dual. http://www.kingston.com/datasheets/KHX26C11T2K2_8X.pdf Thanks Sam!
October 15, 201311 yr Teach me to not pay attention. Should be a good comp and good luck all. I'll likely we watching from the sidelines "again".
October 15, 201311 yr Both scores have been removed from the competition because the kits (with MFR) are not retail. This has been confirmed by Kingston. Dear Massman, Sth wrong with the img upload system? my screenshots totally unreadable after upload to hwbot.org. my result: http://www.hwbot.org/submission/2437691_ => maybe it cause the validation img failed to verify. the origin screenshot: http://www.imagebam.com/image/e2363d281859299 BTW, my 1st acc (id: manhquoc) still can log-in hwbot.org homepage but can not log-in to hwbot forum (error sth about using the same password as id blablabla ... but the pass is totally different with my id, pls kindly help check about this as well) Many Thanks,
October 16, 201311 yr What's with the quality of boards being shipped out? Bought a m6e anditwas garbage.. sometimes boot then some not.. then it finally works then dies on air.. now i get an impact and the pins Are severely damaged, even missing some... wtf... then i had an asrock that wouldn't even boot.. rmas are killing me.. so frustrated
October 16, 201311 yr Author Dear Massman, Sth wrong with the img upload system? my screenshots totally unreadable after upload to hwbot.org. my result: http://www.hwbot.org/submission/2437691_ => maybe it cause the validation img failed to verify. the origin screenshot: http://www.imagebam.com/image/e2363d281859299 BTW, my 1st acc (id: manhquoc) still can log-in hwbot.org homepage but can not log-in to hwbot forum (error sth about using the same password as id blablabla ... but the pass is totally different with my id, pls kindly help check about this as well) Many Thanks, The image are auto-resized if they are too large. But it seems that sometimes the resizing is not done properly. To participate in this competition, submit via the competition page < submit. You will be able to upload the validation screenshot under validation and not system pictures.
October 16, 201311 yr The image are auto-resized if they are too large. But it seems that sometimes the resizing is not done properly. To participate in this competition, submit via the competition page < submit. You will be able to upload the validation screenshot under validation and not system pictures. Thanks sir, u save my XTU score!!! Go strong HOT and hwbot BTW, can you take a look for my main id manhquoc as well, this id can't log-in to forum
October 16, 201311 yr why not for 32m ? Edit : Single Sided SHIT no more 32m Edited October 16, 201311 yr by Hiwa
October 16, 201311 yr OK OK as always i am here for sharing if u bench M6I, u need first slot always warm ( 10 degrees ) put a probe there and it should be full of vaseline, 00 error its or Cpu IMC cbb or wet slots.. when u get 00 or 55 code, warm ONLY first slot ( empty one) and the stick (second slot) will warm automatically, when stick is -70/-80 and empty slot is 10 degrees, you boot , go -120 or lower very fast ( use alu pot and alu HS) on the stick, keep cpu at -90 and SHOT M6I users use only C13 and RTL 64 Bclk ignor boot example 130 Load OS set 132.5 Reboot Load OS without going back into Bios, Set 134.5 reboot find your max 130 Bclk is an example... that can be 135 then 137.5 then 139.5 Edited October 16, 201311 yr by Hiwa
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.