For a while, E-die was only showing up in some 3466 kits and the 3600+ kits. New info says it may be in all G.Skill Ripjaws V and Trident Z produced in Sept 2015 or later.

 

I think we need more evidence first to confirm that completely. I just bought a 3600 Trident Z kit to be sure, myself.

Latest Samsung D-Die kit I saw was 1537, 1538 was already E-Die. I tested around 20 kits from 1538 to 1543, all 3466 and 3600 and one TridentZ 3200, all were E

Damn... should have saved some money then!

 

Just hoping that my 3600 kit is relatively new since they've gone out of stock so many times.

But sammyD are not bad at all!! For example my D kit are better of mine E kit.....

Samsung D I had were 3200 Ripjaw5, solid - but they were no match at low cas especially for my E-kits, but they are good on trcd and can run tight timings as well. If your D are better than your E kit, the Ds must be very good and the E maybe not that strong it seems

Samsung D I had were 3200 Ripjaw5, solid - but they were no match at low cas especially for my E-kits, but they are good on trcd and can run tight timings as well. If your D are better than your E kit, the Ds must be very good and the E maybe not that strong it seems

 

it think because my E-Kit are from a 3200CL16 dimms, so they are very lowbin chips!!

instead, my D-Kit are from a 3466CL16 dimms, and they are better!

 

so i think the best choice is to buy ddr 3466+

Bull, you say new AFR? Is there a new revision?

 

Sorry bass is same kit

Sorry bass is same kit

 

Getting my hopes up that we would actually see retails

Sorry bass is same kit

 

I was so hoping they had released new afr retails too

little more AFR testing @ LN2

 

5Ghz

 

6.2 / 6.0 / 3950 c11

Edited November 5, 20159 yr by l0ud_sil3nc3

In the last few days i was capable of killing 4 skylake cpu.

What i'm doing wrong?

 

So i decide to work around some efficiency stuff

 

 

Yes is a mix of mfr: 1 stick HyperX Fury 2666c15 + 1 stick Geil 3333c16

 

Without waza

 

 

With waza not tight (3200-1.65v/profile)

 

 

With waza supertight

 

 

Next step MFR@LN2 and stop killing cpu if possible...

Edited November 5, 20159 yr by RULE

OMG what did you do to those poor cpus?

i've not idea! This is the problem.

i've not idea! This is the problem.

 

 

Maybe u got faulty mobo. Try to RMA it.

 

When mobo is going mass production. It happended sometimes.

 

Sorry to hear about this

I'll be glad when HOT is over so people will stop hiding tertiary timings :-/

I'm gonna go cold mems first time tomorrow. MFR...should I expect CBB?

I'm gonna go cold mems first time tomorrow. MFR...should I expect CBB?

 

Hey, it'll depend on what memory's you have but -80-90 seems to be a sweet spot for mfr,some kits will go full pot but not always needed as you may be able to still max them out at -80

 

You'll find once you go colder then say -90 the memory will tell you if they don't like it,signs of this would be system will freeze or 55 code ,system won't boot or 32m would become very unstable.Im not sure you'll see a cbb but CB are real on some mfr

I think that mfr are very stressfull to use.....oh my god.....on samsung u can give 2.1v without problem and they keep scaling....

You need to find MFR that likes voltage...

You need to find MFR that likes voltage...

 

Then put the on ln2 ahah

And if you can't find a kit that loves voltage, find one that is okay with it then freeze! Cold will help a bit with scaling, even at the same volts.

For like voltage, what do u mean guys??? 3200 cl12 1.75v???or what???

As the speeds go up, the voltage tolerance goes down. That's why 3000C11 is so popular, many kits can handle a lot of voltage at those speeds.

 

My kit is like this:

 

3000 - 1.85V

3200 - 1.75V

3333 - 1.57V

 

Haven't been able to test higher yet (got some E-Die) and, honestly, I'm not sure how my kit compares to others... just what I have to work with right now.

I know this man.....but what is a good voltage for binning??? Rams that can bench at 3333 cl12 with 1.75v i know that are good.....but maybe is better search some more realistic ddr that can bench at 3333 with 1.65v.....

Another air run today with Asrock complete bios memory profile,no special subs,thirds,I just selected Nicks 3333 tight mfr profile and up memory multi to 3733,so comparing my best run to this run makes this run only .300 slower.If people want efficiency I would suggest to use the correct XP and work on your waza after using the correct profile like that comes with this asrock board.As few have said this board bios is at least 90% or more complete within the memory profiles,all the hard work has been done.

 

Board is also booting now at 1.77v 3866 13-18-18 350 may need over 1.8v to pass 32m, not sure I want to push my memory on air that high,ill see